BE1-GPS100
ORDERING
SAMPLE STYLE NUMBER
The style number identification chart defines the electrical characteristics and operation features included in
BE1-GPS1 00 relay. If the style number were
BE1-GPS100 E3N1 HOU,
the device would have the following:
(E)
5 Amp nominal system with 5 Amp Independent Ground Input
(3)
Three phase voltage sensing
(N)
Not applicable
(1)
48/125VacNdc power supply
(H)
Half Rack drawout case
(O)
ASCII Communications
(U)
Battery backup for real time clock
BE1-GPS100
D D DD DDD
CURRENT SENSING
INPUT TYPE
A) W/0 Independent Gnd Input
B) 1 Amp Independent Gnd Input
5
Nominal
D) W/0 Independent Gnd Input
E)
5 Amp Independent Gnd Input
F)
1 Amp Independent Gnd Input
&,
VOLTAGE SENSING
INPUT TYPE
3) 3-phase sensing
4) 3-phase sensing
with independent
auxiliary input
&&,
COVER
A) S1 cover with
opening for full
HMI access
B) S1 cover with
reset access
only
N) Not applicable
(H1 case)
POWER
SUPPLY
1) 48/125Vac/dc
2) 125/250Vac/dc
3) 24Vdc
CASE
RS-485 PORT
PROTOCOL
O)ASCII
�
1)
Modbus'"
ffi
2)TNP
3) DNP 3.0
H) H1 (Half rack)
NOTES:
S) S1
ffi
ffi.
If case option is H, Cover option must be N .
.ffi
Case option must be H for Current Sensing Input Type B,
E,
or
F
or voltage sensing option to be 4.
�
ASCII communication is standard on ComO (fron1 RS-232) and Com1 (rear RS-232) ports.
ffi
Check with factory for availability.
ffi
Aux
VT
input adds 25 Sync-Check option.
,®.
Option available in H1 case only.
STANDARD ACCESSORIES
OPTION 1
N) None
U)
Battery Backup
for Real Time
Clock
918 0400108
92399221 00
91 08 551 02 1
91 08 550122
H1 Test Case with 1 CT Terminal Block and 18 - position Bottom Terminal Block
Test box to facilitate bench testing.
Adapter plate to mount an S1 case in aGE S2 or Westinghouse FT-21 cutout.
Adapter plate to mount an S1 case in a Westinghouse FT- 32 cutout.
928 99 00017
Escutcheon plate
to panel mount
one H1 relay.
928 99 0001 6
928 99291 00
Adapter bracket with cutout
for ABB FT test switch, to
mount a single H 1 case in
a 1 9" rack.
'
0
I
928 992 41 00
Escutcheon plate
1"
to panel mount two
Adapter b
�
acket to
dovetailed H1 relays.
I II/
mount a smgle H1
lo
/
case in a1 9"rack.
I
'011
§
®Basler Electric
Figure 7A
Cover option A.
Figure
78
Cover option B.
ROUTE 143, BOX 269, HIGHLAND, ILLINOIS U.S.A. 62249
P.A.E. Les Pins, 67319 Wasselonne Cedex FRANCE
PHONE 618-654-2341 FAX 618-654-2351
PHONE (33-3-88) 87-1010 FAX (33-3-88) 87-0808
http://www.basler.com, [email protected]
Printed in U.S.A.
www
. ElectricalPartManuals
. com
