Bartscher F 120 Скачать руководство пользователя страница 15

Страница: 15 / 42

FLOAT TANK

FLOAT VALVE

FREEZER

WATER

FEED LINE

ICE SPOUT

FREEZER WATER

FEED LINE

FREEZER

FLOAT VALVE

ICE SPOUT

FLOAT TANK

FREEZER

FLOAT TANK

FLOAT VALVE

ICE SPOUT

FREEZER

WATER

FEED LINE

WATER CIRCUIT

The water enter in the machine through the

water inlet fitting which incorporates a strainer -

located at the rear side of the cabinet - then it

goes to the water reservoir flowing through a

float valve.

The float reservoir is positioned at the side of the

freezing at such an height to be able to maintain

a constant water level. The water flows from the

reservoir into the bottom inlet of the freezer to

sorround the stainless steel auger which is verti-

cally fitted in the center of the freezer.

In the freezer the incomingwater gets chilled into

soft (slush) ice which is moved upward by the

rotating action of the auger. The auger rotates

counter-clockwisewithin the freezer powered by

a direct drive gear motor and carries the ice

upward along the refrigerated freezer innerwalls

andbydoingso theice gets progressively thicker

and harder.

The ice, being costantly lifted up, meet the teeth

of the ice breakerwhich is fitted on the top end of

the auger,where it gets compacted, cracked and

forced to change from vertical into horizontal

motion to be discharged out, through the ice

spout and chute, into the storage bin.

NOTE.

The presence of thewater in the float

reservoir is detected by a system of two sen-

sors which operates in conjunction with the P.C.

Board. The two sensors use the water as a con-

ductor to maintain a low voltage current flow

between them. In case the water used is very

soft (de-mineralized) or the float reservoir gets

empty the current flow between the sensors

become so weak or is no longer maintained

that, as consequence, the P.C. Board shutoff

the flaker operation with the simultaneous

glowing of the

YELLOW LED

signalling

“Shortage of water”.

PRINCIPLE OF OPERATION

Содержание F 120











































Результаты поиска

Содержание F 120

Отзывы:

Похожие инструкции для F 120

Бренды по названию

Популярные бренды

Bartscher F 120, Руководство по обслуживанию

Результаты поиска

Содержание F 120

Отзывы:

Похожие инструкции для F 120

Бренды по названию

Популярные бренды