Bartscher F 120 Скачать руководство пользователя страница 6

Страница: 6 / 42

A INTRODUCTION

the step-by-step procedures for the installation,

start- up and operation, maintenance and

cleaning for the F80 - F125 Modular Icemakers.

The Electronic Flakers and Superflakers are

quality designed, engineered and manufactu-

red. Their ice making systems are thoroughly

tested providing the utmost in flexibility to fit the

needs of a particular user.

B. UNPACKING AND INSPECTION

Icemaker

1 Call you rauthorizedI Distributor or Dealer for

proper installation.

2 Visually inspect the exterior of the packing

and skid. Any severe damage noted should

be reported to the delivering carrier and a

concealed damage claimformfilled in subjet

to inspection of the contents with the carrier’s

representative present.

3 a) Cut and remove the plastic strip securing

the carton box to the skid.

b) Cut open the top of the carton and remove

the polystyre protection sheet.

c) Pull out the polystyre posts from the cor-

ners and then remove the carton.

d) Lift the whole carton and pull it out from

the device.

4 Remove top and sides panels of the unit and

inspect for any concealed damage.

Notify carrier of your claim for the concealed

damage as stated in step 2 above.

5 Remove all internal support packing and

masking tape.

6 Check that refrigerant lines do not rub again-

st or touch other lines or surfaces, and that

the fan blades move freely.

7 Check that the compressor fits snugly onto

all its mounting pads.

8 See data plate on the rear side of the unit and

check that local main voltage corresponds

with the voltage specified on it.

NOTE.

To retain the safety and performance

built into this icemaker, it is important that

installation and maintenance be conducted

in the manner outlined in this manual.

GENERAL INFORMATION AND INSTALLATION

Содержание F 120











































Результаты поиска

Содержание F 120

Отзывы:

Похожие инструкции для F 120

Бренды по названию

Популярные бренды

Bartscher F 120, Руководство по обслуживанию

Результаты поиска

Содержание F 120

Отзывы:

Похожие инструкции для F 120

Бренды по названию

Популярные бренды