Barrett 2030 Скачать руководство пользователя страница 33

Страница: 33 / 208

BARRETT 2030 HF SSB TRANSCEIVER

33 of 208

Station ID Ranges

Four and six digit networks are all accommodated in the 2030 standard
Selcall system

Station ID range from 000000 to 999999 inclusive (the destination ID

must

either 4 or 6 digits long)

Calling Groups

In four digit format

Allcall

A station sending X000 will be received by stations

X000 - X999 (up to 890 stations*)

Group call

A station sending XX00 will be received by stations XX00 - XX99

(up to 89 stations*)

Sub-group call

A station sending XXX0

will be received by stations XXX0 - XXX9

(up to 9 stations*)

In six digit format

Allcall

A station sending XXX000 will be received by stations XXX000 -

XXX999 (up to 890 stations*)

Group call

A station sending XXXX00 will be received by stations XXXX00 -

XXXX99 (up to 89 stations*)

Sub-group call

A station sending XXXXX0

will be received by stations XXXXX0 -

XXXXX9 (up to 9 stations*)

If using the group call system, stations cannot be programmed to have self IDs

with last digits 000,00,0 as if you tried to call them a group call would occur.

Note:-

Allcall, group call or sub-group call must be enabled, during programming,

on all destination stations for group calling to operate correctly.

Содержание 2030

















































































































































































































Результаты поиска

Содержание 2030

Отзывы:

Похожие инструкции для 2030

Бренды по названию

Популярные бренды

Barrett 2030, Руководство по эксплуатации и установке

Результаты поиска

Содержание 2030

Отзывы:

Похожие инструкции для 2030

Бренды по названию

Популярные бренды