Barrett 2030 Скачать руководство пользователя страница 41

Страница: 41 / 208

BARRETT 2030 HF SSB TRANSCEIVER

Royal Flying Doctor Service (RFDS) alarm

Two-tone alarm 880 Hz + 1320Hz continuous (Australian use only) – alerts the
Royal Flying Doctor Service on RFDS channels.

Press the

button for more than two seconds and less than ten

seconds.

The RFDS alarm will continue transmitting for 10 seconds even if you have

released the

button.

To cancel the RFDS alarm press the

key or the

button.

Note:-

A momentary press of the

button initiates RFDS alarm test mode

which emits the audio tones but does not transmit them. Another momentary press

of the

button or the

key cancels the RFDS alarm test mode.

Note:-

Emergency call settings are set during transceiver programming from the

programming software only.

41 of 208

Содержание 2030

















































































































































































































Результаты поиска

Содержание 2030

Отзывы:

Похожие инструкции для 2030

Бренды по названию

Популярные бренды

Barrett 2030, Руководство по эксплуатации и установке

Результаты поиска

Содержание 2030

Отзывы:

Похожие инструкции для 2030

Бренды по названию

Популярные бренды