manualshive.com logo in svg

Baroness LM180E, Руководство по эксплуатации для владельца

Поделиться
Скачать
Baroness LM180E Скачать руководство пользователя страница 61

Rear Mower Tension

Loosen adjusting nut A.
Tighten adjusting nut B, then change the
length of the rod.
Lower the rear mower unit on a level
surface, then adjust the clearance of the
spring to 1 mm (0.04 in).
Tighten adjusting nut A and make sure that
the rod is fixed securely.
Raise the rear mower unit, then make sure
that the reel cutter (cutting cylinder) will not
rotate when the machine travels.

4

A

3

2

1

y6gulf-001

Rear Mower Tension_001

1

Adjusting nut A

2

Adjusting nut B

3

Rod

4

Rear mower unit

A

1 mm (0.04 in)

1.
2.

3.

4.

5.

Rear Mower Unit

Loosen adjusting nut A.
Tighten adjusting nut B, then change the
length of the rod.
Adjust the belt tension so that the belt
slacks by approximately 10 mm (0.39 in)
when you press the middle of the belt with
your finger at 98 N (10 kgf).
Tighten adjusting nut A and make sure that
the rod is fixed securely.

1

3

2

A

l36w96-006

Rear Mower Unit_001

1

Adjusting nut A

2

Adjusting nut B

3

Rod

A

10 mm (0.39 in)

1.
2.

3.

4.

Maintenance

LM180E

Maintenance

Page 5-19

Maintenance Work

Содержание LM180E









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды