manualshive.com logo in svg

Baroness LM180E, Руководство по эксплуатации для владельца

Поделиться
Скачать
Baroness LM180E Скачать руководство пользователя страница 53

Lubrication

About Lubrication

It is necessary to lubricate moving parts so that
they will not become stuck or damaged.
The locations where lubricant is used are
indicated in "Lubricating Points".
Apply the lubricant.

Lubricating Points

Apply lubricant at the following locations every
50 hours of operation.

1

2

8bq62b-499

Lubricating Points_001

　

Location

No. of

lubricating

points

1

Handle tension

1

2

Brake lever

1

Handle tension
There is one point.

OIL

8bq62b-492

Lubricating Points_002

Brake lever
There is one point.

8bq62b-493

Lubricating Points_003

Maintenance Work

Cleaning of Mower Unit

Important

While cleaning, do not allow water on the
sealed parts of the reel shaft. (Avoid high-
pressure water cleaning.)
Otherwise, it may cause damage to the
machine.

Be sure to clean the mower unit after use.

Stop the engine.
Carefully clean the front and back of the
mower unit with water or compressed air.
Remove any grass wrapped around the reel
cutter (cutting cylinder).

1.

2.

1.
2.

3.

Maintenance

LM180E

Maintenance

Page 5-11

Lubrication

Содержание LM180E









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды