manualshive.com logo in svg

Barnstead International Thermolyne 859 Series, Руководство по обслуживанию

Поделиться
Скачать
Barnstead International Thermolyne 859 Series Скачать руководство пользователя страница 41

History

The following software revisions were used in the NCAT
furnaces.  All software versions are interchangeable and if
in doubt it is always best to update.  The software chip is
located on the Main Logic PC Board (PC859X1) next to
the balance.   A sticker on the chip will indicate the revi-
sion letter.  Hidden Enter Key routine will also prompt the
printer to print the installed revision letter. 

Series

Version

Dates Used

859   

A – D

Used up to 1995

945

D – E

Used in 1996

1087

F – G 

Used in 1997 to 2002

1275

H

Used in 2002 (few months)

1275 

I

Used in production currently

Because the software IC chip is a plug-in style chip (no
soldering necessary to replace) and interchangeable
between every model/series, production dates (beginning
and end) are not important.  

*When ordering new software, use part number
AY1087X3.  The latest version in production will be
shipped.  Barnstead will not provide software versions
used in the past.  Only the latest revision is production.

Versions A and B were Beta site versions.  

Versions C and D were the first two revisions of beta site
software to be used in production.  Operation of an NCAT
was no different between the software revisions.
Changes were all “behind-the-scene” programming to
allow the microprocessor to execute commands faster.

Version E: A feature was added to allow operators to pro-
gram a positive calibration factor.

Version F: Several new operating features were added.  

They include:

1. 

Auto program switching to idle mode.  (Unit will
stop test automatically when the sample is sta-
ble and revert to idle mode, placing an asterisk
next to endpoint.  This feature frees up opera-
tor’s time and increases the number of tests that
can be run in a days time.)

41

Software

Main Logic Board - Software I.C.

Содержание Thermolyne 859 Series























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды