Barnstead International Thermolyne 859 Series Скачать руководство пользователя страница 26

Страница: 26 / 118

Press the ON button again. “Span” is displayed
followed by “C 0g”.

Press the ON button again to start the Span cal-
ibration. “-C-“ is displayed followed by the value
of mass which must be placed on the platform
such as “C 2000g”. NOTE: DO NOT DISTURB
THE BALANCE WHEN “-C-“ IS DISPLAYED.

Repeatedly press the MODE button to select the
percentage of the mass on the display. (25% =
2000g, 50% = 4000g, 75% = 6000g, 100% =
8000g.)

10. Place the required mass on the calibration plate.

11. Press the ON button. “-C- “ displayed while the

balance calibrates. NOTE: DO NOT DISTURB
THE BALANCE WHEN “-C-“ IS DISPLAYED.

12. Display will automatically indicate “S” followed

by the calibration weight when calibration is
complete.

13. Remove the mass from the calibration platform.

“S 0.00g” is displayed indicating the balance is
now in weighing mode and the SPAN calibration
is complete.

14. Power down the NCAT unit.

15. Remove the calibration platform and reinstall the

hearth plate, ensuring it is centered on the four
ceramic support posts.

16. Calibration

complete.

OHAUS B

ALANCE

Содержание Thermolyne 859 Series























































































































Результаты поиска

Содержание Thermolyne 859 Series

Отзывы:

Бренды по названию

Популярные бренды

Barnstead International Thermolyne 859 Series, Руководство по обслуживанию

Результаты поиска

Содержание Thermolyne 859 Series

Отзывы:

Бренды по названию

Популярные бренды