manualshive.com logo in svg

Barnstead International Thermolyne 859 Series, Руководство по обслуживанию

Поделиться
Скачать
Barnstead International Thermolyne 859 Series Скачать руководство пользователя страница 38

38

Printer Change (Production)

Seiko to Martel (1087 to 1275)

The Seiko printer used in production of the 859, 945 and 1087 series NCAT is obsolete.  The new printer is
manufactured by Martel and will be used in production starting with the 1275 series NCAT in Oct/Nov of 2001.
The software is being changed. The reason for the software update is the degree symbol on the front display
would not print with the Martel. 

SOFTWARE UPDATE: REV H software was only used in production for a couple of months.  Behind the
scene changes were made and we are now using Rev I in production. 

Part Number

Description

AYX3

Thermal Printer (Seiko)

AYX28

Thermal Printer (Martel)

DL1087X8

Keypad RPO for Seiko printers

DL1275X4

Keypad RPO for Martel Printers

P

RINTER

DL1087X8 keypad - 
1087 series only
(Seiko printer)

DL1275X4 keypad - 
1275 series only
(Martel printer)

DL859X11A keypad - 
859 and 945 series only
(Seiko printer)

Содержание Thermolyne 859 Series























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды