![background image](http://html1.mh-extra.com/html/barco/hdf-w-series/hdf-w-series_service-manual_474148039.webp)
5. Troubleshooting
Code 2006: “Read lamp status failed” (Error)
Situation
Solution
Projector has no communication with
the LPS module.
1.
Check if the CTLB-IN wire unit is connected with the LPS module (reference 1
image 5-3).
2.
Check if the CTLB-IN wire unit is connected with the Power Distribution board
(reference 9 image 5-4).
3.
Check if the yellow wire unit (reference 3image 5-4 & image 5-5) between the
Power Backplane and the rear side of the Input & Communication unit is properly
connected.
Code 2007: “LPS invalid parameters” (Error)
Situation
Solution
The parameters sent by the projector
controller to the LPS module are
corrupt of not valid.
1.
Ensure that the latest
fi
rmware for the LPS module is installed.
2.
Ensure that the latest version of projector software is installed.
3.
Reboot the projector.
4.
If the problem persist, contact Barco for further instructions.
Code 2008: “LPS failure fan 1 & 2” (Error)
Situation
Solution
The supply voltage or the drivers for
the LPS fans fail.
Replace one or both LPS modules. See "Lamp Power Supply", page 169.
Code 2009: “LPS start-up fail PFC power stage” (Error)
Situation
Solution
Failure in the circuitry part of the
Power Factor Corrector (PFC) inside
the LPS modules.
Replace one or both LPS modules. See "Lamp Power Supply", page 169.
Code 2010: “LPS start-up fail LPS power stage” (Error)
Situation
Solution
Failure in the circuitry of the Lamp
Power Supply (LPS).
Replace one or both LPS modules. See "Lamp Power Supply", page 169.
Code 2011: “LPS boost voltage generation failed” (Error)
Situation
Solution
LPS modules fail to generate the
boost voltage to ignite the lamp.
Replace one or both LPS modules. See "Lamp Power Supply", page 169.
Code 2012: “LPS no lamp ignition detected” (Error)
Situation
Solution
After the LPS module has generated
a boost voltage to ignite the lamp, no
lamp ignition was detected.
1.
Check the runtime of the lamp. In case of an old lamp replace with a new lamp.
2.
Check the connections between the LPS module and the SPG unit.
3.
Replace one or both LPS modules. See "Lamp Power Supply", page 169.
Code 2013: “LPS output power too low” (Error)
Situation
Solution
The lamp is ignited but the power
delivered by the LPS modules is too
low for the lamp.
1.
Check the runtime of the lamp. In case of an old lamp replace with a new lamp.
2.
Replace one or both LPS modules. See "Lamp Power Supply", page 169.
Code 2014: “LPS output power too high” (Error)
Situation
Solution
The lamp is ignited but the power
delivered by the LPS modules is too
high for the lamp.
1.
Replace the lamp. See "Lamp and lamp house", page 117.
2.
Replace one or both LPS modules. See "Lamp Power Supply", page 169.
R5905312 HDF W SERIES 24/01/2013
35
Содержание HDF W series
