R5910886 /02
G60
6
•
Let the projector cool down completely before storing. Remove cord from the projector when storing.
To prevent projector damage
•
Always remove lens cap before switching on the projector. If the lens cap is not removed, it may melt due to the high energy light
emitted through the lens. Melting the lens cap may permanently damage the surface of the projection lens.
•
The air filters of the projector must be cleaned or replaced on a regular basis. Cleaning the booth area would be monthly minimum.
Neglecting this could result in disrupting the air flow inside the projector, causing overheating. Overheating may lead to the projector
shutting down during operation.
•
The projector must always be installed in a manner which ensures free flow of air into its air inlets and unimpeded evacuation of the
hot air from its cooling system.
•
If more than one projector is installed in a common projection booth, the exhaust air flow requirements are valid for EACH individual
projector system. Note that inadequate air extraction or cooling will result in decreased life expectancy of the projector as a whole as
well as causing premature failure of the lasers.
•
In order to ensure that correct airflow is maintained, and that the projector complies with Electromagnetic Compatibility (EMC)
requirements, it should always be operated with all of its covers in place.
•
Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from
overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. The device should not
be placed in a built-in installation or enclosure unless proper ventilation is provided.
•
Ensure that nothing can be spilled on, or dropped inside the projector. If this does happen, switch off and unplug the mains supply
immediately. Do not operate the projector again until it has been checked by qualified service personnel.
•
Do not block the projector cooling fans or free air movement around the projector.
•
Do not use this equipment near water.
•
Special care for Laser Beams: Special care should be used when DLP projectors are used in the same room as high power laser
equipment. Direct or indirect hitting of a laser beam on to the lens can severely damage the Digital Mirror Devices
™
in which case
there is a loss of warranty.
•
Never place the projector in direct sun light. Sun light on the lens can severely damage the Digital Mirror Devices
™
in which case
there is a loss of warranty.
•
Save the original shipping carton and packing material. They will come in handy if you ever have to ship your equipment. For
maximum protection, repack your set as it was originally packed at the factory.
•
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Never use strong solvents, such as thinner or benzine, or abrasive cleaners, since these will damage the cabinet. Stubborn stains may
be removed with a cloth lightly dampened with mild detergent solution.
•
To ensure the highest optical performance and resolution, the projection lenses are specially treated with an anti-reflective coating,
therefore, avoid touching the lens. To remove dust on the lens, use a soft dry cloth. Do not use a damp cloth, detergent solution, or
thinner.
•
Rated operating ambient temperature: ta= 5 °C (41 °F) to 40 °C (104 °F).
•
Rated operating humidity: 10% RH to 85% RH (non-condensing). This projector can be set to any angle within 360° range.
•
Allowing proper space around the projector is critical for proper air circulation and cooling of the unit. The dimensions shown here
indicate the minimum space required.
100 cm
(39.4”)
100 cm
(39.4”)
100 cm
(39.4”)
100 cm
(39.4”)
30 mm
(1.2”)
10.1 mm
(0.4”)
1
2
Image 1-1
1
Bottom intake vents.
2
Ceiling mount plate.
•
For ceiling mounted installations, make sure to leave 30 mm (1.2
”
) between the ceiling mount and the bottom intake vents of the
projector.
To prevent battery explosion
•
Danger of explosion if battery is incorrectly installed.
•
Replace only with the same or equivalent type recommended by the manufacturer.
•
For disposal of used batteries, always consult federal, state, local and provincial hazardous waste disposal rules and regulations to
ensure proper disposal.
On servicing
•
Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage potentials and
risk of electric shock.
•
Refer all servicing to qualified service personnel.
Содержание G60 Series
Страница 1: ...ENABLING BRIGHT OUTCOMES Safety manual G60...
