R5910886 /02
G60
5
FOR PROFESSIONAL USE ONLY means installation can only be carried out by Barco AUTHORIZED PERSONNEL familiar with
potential hazards associated with high intensity light beams.
1.2 Important safety instructions
To prevent the risk of electrical shock
•
This product should be operated from a mono phase AC power source.
•
This apparatus must be grounded (earthed) via the supplied 3 conductor AC power cable. If none of the supplied power cables are the
correct one, consult your dealer. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete
outlet. Do not defeat the purpose of the grounding-type plug.
•
Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. To disconnect the
cord, pull it out by the plug. Never pull the cord itself.
•
Use only the power cord supplied with your device. While appearing to be similar, other power cords have not been safety tested at the
factory and may not be used to power the device. For a replacement power cord, contact your dealer.
•
Do not operate the projector with a damaged cord. Replace the cord.
•
Do not operate the projector if the projector has been dropped or damaged until it has been examined and approved for operation by a
qualified service technician. Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
•
If an extension cord is necessary, a cord with a current rating at least equal to that of the projector should be used. A cord rated for less
amperage than the projector may overheat.
•
Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts
that could result in a risk of fire or electrical shock.
•
Do not expose this projector to rain or moisture.
•
Do not immerse or expose this projector in water or other liquids.
•
Do not spill liquid of any kind on this projector.
•
Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualified service personnel before
resuming operations.
•
Do not disassemble this projector, always take it to an authorized trained service person when service or repair work is required.
•
Do not use an accessory attachment which is not recommended by the manufacturer.
•
Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will prevent damage to the device due to lightning and AC power-line surges.
To prevent personal injury
•
To prevent injury and physical damage, always read this manual and all labels on the system before connecting to the wall outlet or
adjusting the projector.
•
To prevent injury, take note of the weight of the projector.
•
To prevent injury, ensure that the lens and all covers are correctly installed. See installation procedures.
•
Warning: high intensity light beam. NEVER look into the lens ! High luminance could result in damage to the eye.
•
Warning: extremely high brightness laser: This projector uses extremely high brightness laser. Never attempt to look directly into the
lens or at the laser.
•
Before attempting to remove any of the projector
’
s covers, you must turn off the projector and disconnect from the wall outlet.
•
When required to switch off the projector, to access parts inside, always disconnect the power cord from the power net.
•
The power input at the projector side is considered as the disconnect device. When required to switch off the projector, to access parts
inside, always disconnect the power cord at the projector side. In case the power input at the projector side is not accessible (e.g.
ceiling mount), the socket outlet supplying the projector shall be installed nearby the projector and be easily accessible, or a readily
accessible general disconnect device shall be incorporated in the fixed wiring.
•
Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious damage to it and possible injury
to the user.
•
It is hazardous to operate without lens or shield. Lenses, shields or ultra violet screens shall be changed if they have become visibly
damaged to such an extent that their effectiveness is impaired. For example by cracks or deep scratches.
•
Exposure to UV radiation: Some medications are known to make individuals extra sensitive to UV radiation. The American Conference
of Governmental Industrial Hygienists (ACGIH) recommends occupational UV exposure for an-8 hour day to be less than 0,1 micro-
watts per square centimeters of effective UV radiation. An evaluation of the workplace is advised to assure employees are not
exposed to cumulative radiation levels exceeding these government guidelines. The exposer of this UV radiation is allowed for only 1
hour per day for maintenance and service persons.
To prevent fire hazard
•
Do not place flammable or combustible materials near the projector!
•
Barco large screen projection products are designed and manufactured to meet the most stringent safety regulations. This projector
radiates heat on its external surfaces and from ventilation ducts during normal operation, which is both normal and safe. Exposing
flammable or combustible materials into close proximity of this projector could result in the spontaneous ignition of that material,
resulting in a fire. For this reason, it is absolutely necessary to leave an
“
exclusion zone
”
around all external surfaces of the projector
whereby no flammable or combustible materials are present. The exclusion zone must be not less than 100 cm (39.4
”
) for all DLP
projectors. The exclusion zone on the lens side must be at least 5 m. Do not cover the projector or the lens with any material while the
projector is in operation. Keep flammable and combustible materials away from the projector at all times. Mount the projector in a well-
ventilated area away from sources of ignition and out of direct sun light. Never expose the projector to rain or moisture. In the event of
fire, use sand, CO2 or dry powder fire extinguishers. Never use water on an electrical fire. Always have service performed on this
projector by authorized Barco service personnel. Always insist on genuine Barco replacement parts. Never use non- Barco
replacement parts as they may degrade the safety of this projector.
•
Slots and openings in this equipment are provided for ventilation. To ensure reliable operation of the projector and to protect it from
overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the projector too close
to walls, or other similar surface. This projector should never be placed near or over a radiator or heat register. This projector should
not be placed in a built-in installation or enclosure unless proper ventilation is provided.
•
Projection rooms must be well ventilated or cooled in order to avoid build up of heat.
Содержание G60 Series
Страница 1: ...ENABLING BRIGHT OUTCOMES Safety manual G60...
