![background image](http://html1.mh-extra.com/html/barco/flm-hd18/flm-hd18_user-manual_4133035012.webp)
1. Safety
To prevent battery explosion
•
Danger of explosion if battery is incorrectly installed.
•
Replace only with the same or equivalent type recommended by the manufacturer.
•
Dispose of used batteries according to the manufacturer’s instruction.
To prevent fire hazard
•
Warning “Risk of fire”. Do not place flammable or combustible materials near the projector !
This projector radiates heat on its external surfaces and from ventilation ducts during normal operation, which is both normal
and safe. Exposing flammable or combustible materials into close proximity of this projector could result in the spontaneous
ignition of that material, resulting in a fire. For this reason, it is absolutely necessary to leave an “exclusion zone” around all
external surfaces of the projector whereby no flammable or combustible materials are present. The exclusion zone must be not
less than 40 cm (16”) for all Barco DLP projectors. The exclusion zone on the lens side must be at least 2 meter (80”).
•
Do not cover the projector or the lens with any material while the projector is in operation.
•
To reduce the lamp heat of the projector, switch the projector first to standby and let the projector lamp cool down for at least 5
minutes. Then the projector may be switched off with the power switch.
•
Mount the projector in a well ventilated area away from sources of ignition and out of direct sun light.
•
Never expose the projector to rain or moisture.
•
In the event of fire, use sand, CO
2
, or dry powder fire extinguishers; never use water on an electrical fire.
•
This product should never be placed near or over a radiator or heat register.
•
This projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
•
Projection rooms must be well ventilated or cooled in order to avoid build up of heat.
On servicing
•
Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage potentials
and risk of electric shock.
•
Refer all servicing to qualified service personnel.
•
Fence off a restricted area of at least 3 meters around the projector using an eye-catching fence and “KEEP OUT” sings. This
to prevent unauthorized persons coming near the projector during servicing.
•
Unplug this product from the wall outlet and refer servicing to qualified service technicians under the following conditions:
- When the power cord or plug is damaged or frayed.
- If liquid has been spilled into the equipment.
- If the product has been exposed to rain or water.
- If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are
covered by the operating instructions since improper adjustment of the other controls may result in damage and will often
require extensive work by a qualified technician to restore the product to normal operation.
- If the product has been dropped or the cabinet has been damaged.
- If the product exhibits a distinct change in performance, indicating a need for service.
•
Replacement parts: When replacement parts are required, be sure the service technician has used original Barco replacement
parts or authorized replacement parts which have the same characteristics as the Barco original part. Unauthorized substitu-
tions may result in degraded performance and reliability, fire, electric shock or other hazards. Unauthorized substitutions may
void warranty.
•
Safety check: Upon completion of any service or repairs to this projector, ask the service technician to perform safety checks
to determine that the product is in proper operating condition.
1.3
Important warnings concerning FLM flight cases
Important warnings concerning stacking/transporting FLM rental flight cases
•
Stack maximum two (2) FLM rental flight cases high. Never higher.
•
Surface on which flight case is standing must be level to ensure that the total load is evenly spread out among the four wheels.
The surface must also be able to support the load safely.
•
Before stacking or transporting flight cases, check the wheels and their fixation screws for wear or defects.
•
Before stacking or transporting flight cases, check that the four lock handles on each flight case are in good working order and
locked securely.
•
When stacked, make sure the wheels of the upper flight case are precisely positioned in the stacking dishes of the flight case
below.
•
Stacked flight cases may not be moved. Before stacking, the lower flight case must already be in its final resting position before
placing the second upon it.
•
Never stack loaded flight cases in a truck or other transport medium, unless each flight case is rigidly strapped tight.
•
In the event of a wheel breaking, flight cases must be rigidly strapped tight to prevent a stack collapsing.
•
Use an appropriate forklift to raise flight cases and take the necessary precautions to avoid personnel injury.
8
R5976986 FLM HD18 01/09/2006
Содержание FLM HD18
