![background image](http://html1.mh-extra.com/html/barco/f90-w13wuxga/f90-w13wuxga_user-manual_4186791026.webp)
2. Getting to know the projector.
Projector controlling
When the address is set, the projector can be controlled now:
•
with the RCU: only for addresses between 1 and 31.
Broadcast Address
Every projector has a broadcast (common) address ’0’ or ’1’. The default address is ’0’.
The choice between ’0’ and ’1’ can be selected in the GUI: “
System Settings
”
→
“
Communication
”
→
“IR Control
“.
Placing new batteries in the remote control or plugging the remote to a projector via a cable will automatically
reset the address back to its default value ’0’.
2.8.2
Displaying and Programming addresses into the RCU
Displaying the Projector Address on the Screen.
1. If the projector is on, press the menu key and navigate to the Status page. The projector address and the broadcast address can
be seen under the Communication heading.
The projector’s address is displayed on the LCD status screen and / or the OSD.
How to Program an Address into the RCU?
1. Press the
Address
button until the
Button pressed indicator
lights up continuously (proximately 5 seconds).
2. Enter the address with the digit buttons within the time the indicator lights up (also proximately 5 seconds).
Note:
That address can be any value between 0 and 31.
Tip:
A few examples:
To enter address 3, press "3" digit button on the RCU to set the RCU’s address to 3 and wait until the button pressed
indicator is out. Alternatively, you can also press “0” and “3”. This way, the button pressed indicator goes out immediately.
To enter address 31, then press “3” and “1” on the digit button on the RCU and the button pressed indicator goes out
immediately.
2.9
Connector panel
General
The source input panel is located at the back of the projector. For source speci
fi
cations, see table below.
Image 2-10
Name
Pcs
Description
Purpose
DMX IN
1
DMX 512 input
For Projector Control
DMX OUT
1
DMX 512 output
For Projector Control
RS-232
1
9–pin DB9 connector
For Projector Control. Allows for wired remote control and
monitoring of many projector functions used in installation
environments
Sync
3
BNC Sync Port IN/OUT; Bidirectional
mini-DIN (1x 3D sync Out, and 2x
Sync In/Out)
For Projector ControlThis is mainly used in multiple projector
installations with requirement of synchronization between
the units
Trigger
3 (one in
front, two
on rear
panel)
12VDC - 0,5A (6W)
For Controlling Peripherals, like motorized screens, curtains
etc. Give 12V output when projector are switched on
RC
1
Jack connector for wired remote
For Projector Control
USB
3
USB 2.0 type A, 4 pin( 2x Rear and
1x Front)
For Software upgrade
22
601–426 F70 SERIES 24/10/2017
Содержание F90 - W13WUXGA
