![background image](http://html1.mh-extra.com/html/barco/dp2k-19b/dp2k-19b_installation-manual_4105057015.webp)
2. General
2. GENERAL
About this chapter
Read this chapter before installing your B-series projector. It contains important information concerning installation requirements
for the B-series projector, such as minimum and maximum allowed ambient temperature, humidity conditions, required safety area
around the installed projector, required power net, etc.
Furthermore, careful consideration of things such as image size, ambient light level, projector placement and type of screen to use
are critical to the optimum use of the projection system.
About B-series projectors
This manual can be used for the following projectors :
•
DP2K-19B
•
DP2K-23B
•
DP2K-P
•
DP4K-19B
•
DP4K-23B
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guar-
antee. Observing the speci
fi
cation mentioned in this chapter is critical for projector performance. Neglecting
this can result in loss of warranty.
Overview
•
•
•
•
2.1
Installation requirements
Environment conditions
Table below summarizes the physical environment in which the B-series projector may be safely operated or stored.
Environment
Operating
Non-Operating
Ambient Temperature
10 °C (50 °F) to 35 °C (95 °F)
-15°C (5°F) to 60°C (140°F)
Humidity
5% to 85% RH Non-condensed
5% to 95% RH Non-Condensed
Altitude
-60 (-197Ft) to 3000m (9843Ft)
-60 (-197Ft) to 10000m (32810Ft)
Let the projector acclimatize after unpacking. Neglecting this may result in a startup failure of the Light Pro-
cessor Unit.
Cooling requirements
The projector is fan cooled and must be installed with suf
fi
cient space around the projector head, minimum 20 cm (8 inch) to ensure
suf
fi
cient air
fl
ow. It should be used in an area where the ambient temperature, as measured at the projector air inlet , does not
35°C (+95°F).
The installation of an
exhaust system
is
MANDATORY
. The installed exhaust blower must remove an air volume of minimum
10
m
3
/min (350 CFM)
measured at the exhaust output of the projector.
Main Power requirements
The B-series projector operates from a nominal mono phase power net with a separate earth ground PE.
Projector
Power requirements
DP2K-19B
200-240 VAC, 50-60Hz, 24A at 200 VAC
DP2K-23B
200-240 VAC, 50-60Hz, 30A at 200 VAC
R5905067 DPXK-19B/23B/P 17/09/2012
9
Содержание DP2K-19B
