Barco DP2K-19B, Руководство по установке

Страница: 20 / 125

2. General
Mechanical check
This check should con fi rm that there are no broken knobs or connectors, that the cabinet and panel surfaces are free of dents and
scratches, and that the operating panel is not scratched or cracked. The Barco Sales and Service of fi ce should be noti fi ed as soon
as possible if this is not the case.
Tamper labels
During installation please inspect the tamper labels, if they are damaged please contact Barco tech support.
The tamper labels are required by DCI to provide easy visual indication if the equipment was tampered with. The projectors are
tested and labeled for shipping to ensure that the system was not compromised before reaching the customers
fi nal destination.
These tamper labels can be found behind the input cover. See "Removal of the input cover", page 84.
2.4 Installation process overview
Let the projector acclimate to the ambient temperature after unpacking. Neglecting this may result in a startup
failure of the light processor unit.
Set up from A to Z
After you have unpacked and checked the projector, you can start with the installation process of your B-series projector. This
chapter gives you an overview of all the different stages in the installation process which you have to follow to set your B-series
projector up and running. Each stage is brie
fl y described and refers to more detailed step by step procedures in this manual. Use
this overview as a checklist to ensure that you have followed all stages in the setup process of your B-series projector.
Set up from A to Z
1. Check if all installation requirements are ful fi lled such as the environment conditions of the installation area, capacity of the
exhaust system, electrical facilities, etc. Note that a solid pedestal is required to support the projector head. For more info see
topic "Installation requirements", page 9.
2. Physical installation of the projector upon its pedestal and connecting the air outlet of the projector with the exhaust system.
Note that the exhaust system is MANDATORY. See chapters "Positioning the B-series projector at port window", page 17, and
"Installation of the exhaust system", page 19.
3. Electrical connection with the power net . See chapter "Connecting the DPxK-19B/23B/P with the power net", page 22.
4. Installation of a suitable UPS unit or bypass the power in and outlet for the projector electronics. See chapters "Power loop
through to the projector electronics", page 23 or "Connecting a UPS to the projector electronics", page 24.
5. Installation of the xenon lamp in case the xenon lamp is not installed in the lamp house yet. To install the xenon lamp the lamp
house has to be removed from the projector. To install the xenon lamp correctly and in a safe manner, see the detailed step by
step procedures in the chapter "Installation of the xenon lamp in manual S/M Lamp House", page 34.
6. Installation of the lens . First select an appropriate lens which throw ratio covers the screen size and the projector - screen
distance. Then install the lens in the lens holder of the projector. For more information about available lenses, lens selection and
lens installation see chapter "Lens installation", page 47.
7. Installation of the Communicator Touch Panel . See chapter "Communicator Touch Panel", page 67.
8. Alignment of the projected image on the screen . The projector can now be switched on to project its fi rst image (test pattern)
on the screen. Then the image can be aligned with the screen size of the application. Follow the next steps to achieve that:
a) Place the
ON/OFF switch of the projector in the ”I” position. As a result the projector starts to initialize. The status lights of
the projector lights up GREEN once the projector is initialized.
b) Press the STANDBY button on the local keypad to activate the lamp.
c) Press the DOWSER button on the local keypad to open the dowser of the projector. The dowser is open if the color of the
DOWSER button is GREEN.
d) Press the TEST PATTERN button on the local keypad to project one of the internal test patterns of the projector on the screen.
e) Use the lens ZOOM , SHIFT and FOCUS buttons on the local keypad the match the projected image with the screen. Tilt the
projector in case you can not SHIFT the image completely upon the screen. See "Lens shift, zoom & focus", page 50.
9. Resetting the lamp parameters . The “LAMP INFO” parameters which are stored on the controller board of the projector MUST
be updated after each installation of an xenon lamp inside the lamp house. Neglecting this update will result in poor performance
and short life time of the xenon lamp. See chapter "Resetting the lamp parameters", page 40.
10. Realignment of the xenon lamp in its re fl ector . For optimal performance of the xenon lamp it is required to realign the lamp
after installation in the lamp house. See "Realignment of the lamp in its re fl ector (manual Lamp House)", page 43 for more
information.
11. Adjusting the light path . Normally the lens holder and the convergence of the projector is perfectly adjusted at the factory.
Nevertheless, some applications require a readjustment of the lens holder, convergence or both. See procedure "Scheimp fl ug
adjustment", page 51, to adjust the Scheimp fl ug and see "Convergence", page 101 to adjust the convergence of the light path.
14 R5905067 DPXK-19B/23B/P 17/09/2012