Barbecook BC-GAS-2003, Руководство пользователя

Страница: 30 / 300

www.barbecook.com 30
9.2.2 Using a match
1. 1. Place a match in the match holder.
2. Open the lid and set the control knobs for the main burners
to OFF.
3. If no other burner has yet been ignited, open the gas supply
and wait for ten seconds for the gas to stabilize.
4. Strike the match and hold it around 13 mm away from the
burner.
5. Set the control knob for one burner to HIGH.
Start by igniting one main burner first. Never ignite all
main burners at the same time.
6. If the burner does not ignite within 5 seconds, set the
control knob for the burner to OFF, close the gas supply,
and wait for 5 minutes to allow the accumulated gas to
escape.
7. Attempt to ignite the burner again. If this does not work,
consult "14. Rectifying problems" in order
to identify the cause of the problem.
8. If one burner has been ignited, you can ignite the other
burners by setting the relevant control knobs to HIGH.
9.3. Igniting the side burner
The side burner can only hold pans with a maximum
weight of 9 kg, a maximum diameter of 220 mm and a
minimum diameter of 120 mm.
9.3.1 Using the igniter
1. Open the lid and set the control knob for the side burner
to OFF.
2. If no other burner has yet been ignited, open the gas supply
and wait for ten seconds for the gas to stabilize.
3. Press the igniter until you hear sparking.
4. Continue to press the igniter and set the control knob for
the side burner to HIGH.
5. If the burner does not ignite after three attempts, set the
control knob for the burner to OFF, close the gas supply,
and wait for 5 minutes to allow the accumulated gas to
escape.
6. Attempt to ignite the side burner again. If it still does not
ignite, attempt to ignite the burner with a match (see 9.2.2.
"Using a match") or consult "14. Rectifying problems" in
order to identify the cause of the problem.
9.3.2 Using a match
1. Place a match in the match holder.
2. Open the lid and set the control knob for the side burner to
OFF.
3. If no other burner has yet been ignited, open the gas supply
and wait for ten seconds for the gas to stabilize.
4. Strike the match and hold it around 13 mm away from the
side burner.
5. Set the control knob for the side burner to HIGH.
6. If the side burner does not ignite within 5 seconds, set the
control knob for the burner to OFF, close the gas supply,
and wait for 5 minutes to allow the accumulated gas to
escape.
7. Attempt to ignite the side burner again. If this does not
work, consult "14. Rectifying problems" in order to identify
the cause of the problem.
9.4. Switching the burners off
If the burners will not be used for some time, they must be
switched off. Proceed as follows:
1. Close the gas supply.
2. Set the control knobs for the burners to OFF.
By closing the gas supply first, you ensure there is no
longer any gas present in the appliance.
9.5. Re-igniting the burners
If a burner goes out in use, proceed as follows:
1. Open the lid and close the gas supply.
2. Set all control knobs to OFF and wait for 5 minutes
for the accumulated gas to escape.
3. Re-ignite the burner(s) as outlined in "9.2.1. Using the
igniter".
9.6. Checking the flames
Whenever you ignite a burner, you must check its flames.
A perfect flame will be almost blue, with a small amount of
yellow at the top. Sporadic yellow flames are normal and safe.
If there is a problem with the flames, take one of the following
measures to rectify it:
The flames are... Proceed as follows...
Low and entirely yellow 1. Close the gas supply
immediately and set all control
knobs to OFF.
2. Consult "14. Rectifying
problems" in order
to identify the cause of the
problem. The venturi tubes are
most likely blocked.