Banner SLLVE23-1050 Скачать руководство пользователя страница 27

Страница: 27 / 76

Receiver

Emitter

Receiver

Emitter

Receiver

Emitter

Both cable ends down

Both cable ends up

Orientation parallel to floor with both

cable ends pointing in the same

direction

Figure 12. Examples of Correct Emitter/Receiver Orientation

Receiver

Emitter

Receiver

Emitter

Cable ends point in opposite directions

Problem: Voids in defined area

Emitter and receiver not parallel to each other

Problem: Reduced excess gain

Figure 13. Examples of Incorrect Emitter/Receiver Orientation

5.1.8 Installation of Multiple Systems

Whenever two or more EZ-SCREEN LS Basic emitter and receiver pairs are adjacent to one another, optical crosstalk may

take place between the systems. To minimize optical crosstalk, alternate the positions of the emitters and receivers (see

Figure 14

on page 28).

When three or more systems are installed in the same plane (as shown in

Figure 14

on page 28), optical crosstalk may

occur between sensor pairs whose emitter and receiver lenses are oriented in the same direction. In this situation, eliminate

optical crosstalk by mounting these sensor pairs exactly in line with each other within one plane, or by adding a mechanical

barrier between the pairs.
To further aid in avoiding crosstalk, the sensors feature two selectable scan codes. A receiver set to one scan code will not

respond to an emitter set to another code.

EZ-SCREEN

LS Basic Safety Light Screen

www.bannerengineering.com - Tel: 763.544.3164

Содержание SLLVE23-1050












































































Результаты поиска

Содержание SLLVE23-1050

Отзывы:

Бренды по названию

Популярные бренды

Banner SLLVE23-1050, Инструкция по эксплуатации

Результаты поиска

Содержание SLLVE23-1050

Отзывы:

Бренды по названию

Популярные бренды