Banner LTF Скачать руководство пользователя страница 51

Страница: 51 / 60

June 22, 2023

LTF Time Of Flight Laser Distance Sensor Instruction Manual

Chapter Contents

Message/Indicator

Description

Resolution

Fail/Out of Range

The TEACH failed, the target is out of range. The target
might have moved out of range after the TEACH

process began.

TEACH the target within the measurement range.

Fail/OfSt Out of Range

The TEACH failed. The target is in range but the offset

value caused the setpoint(s) to be out of range.

Adjust the offset value or target distance to keep the setpoint(s)

within the measurement range.

MIN Wnd xx mm (xx in)

The adjusted or taught window size is too small; the
minimum window size is displayed.

The sensor automatically adjusts the window size to maintain
the minimum window size and completes the adjust or TEACH

operation.

xxxx < NEAR

The threshold (xxxx) is less than the minimum sensing
range. xxxx could be 4mA Pt (0V Pt), 20mA Pt (10V Pt)

or SPt1.

The desired window size is maintained, but the usable portion
of the window is restricted to be within the defined sensing

range.

xxxx > FAR

The threshold (xxxx) is greater than the maximum sens-

ing range. xxxx could be 4mA Pt (0V Pt), 20mA Pt (10V

Pt) or SPt2.

The desired window size is maintained, but the usable portion
of the window is restricted to be within the defined sensing

range.

OutRnge

The target is out of range, too dark, or the sensor is not

measuring.

Move the target within the measurement range.

< NEAR

During RUN mode the target is detected, but is inside

the NEAR measuring range.

The sensor can reliably detect targets up to the face of the sen-

sor, and the Discrete Output state is valid. The Analog Output

cannot be used to measure distances inside the NEAR measur-
ing range.

Power LED is flashing green

The sensor input is set to laser enable and the input is

not active.

See

Input Type

" on page 35

All LEDs are flashing

The laser shuts off, the Power LED flashes green, the
Output LEDs flash amber at 1 Hz, and the display is
blank.

The sensor has experienced a fault.

Contact Banner Engineering to resolve.

Type Sync Slave

The slave mode sensor does not see the master's

pulse.

Make sure that the master mode sensor is configured and func-

tioning properly. Check the input wire connection between the

master and slave.

Troubleshooting

Chapter 7

Содержание LTF



























































Результаты поиска

Содержание LTF

Отзывы:

Бренды по названию

Популярные бренды

Banner LTF, Инструкция по эксплуатации

Результаты поиска

Содержание LTF

Отзывы:

Бренды по названию

Популярные бренды