Banner LTF Скачать руководство пользователя страница 15

Страница: 15 / 60

June 22, 2023

LTF Time Of Flight Laser Distance Sensor Instruction Manual

Remote Input Map

Set Window Size to X1 , then back to Run mode

Set Window Size to X2 , then back to Run mode

Set Window Size to X3 , then back to Run mode

Set Window Size to X4 , then back to Run mode

Set Window Size to X5 , then back to Run mode

Set Window Size to X6 , then back to Run mode

Select Slope Positive, then back to Run mode

Select Slope Negative, then back to Run mode

Enter Remote TEACH RMT TCH with measurement value

Enter Remote Setup REMOTE SETUP

Teaching..(4mA)

Tch4mA with measurement value, then to Tch20mA

Teaching..(20mA)

Tch20mA with measurement value, then back to Run mode

REMOTE TEACH

REMOTE SETUP

Slope

Slope value (positive or negative)

Window Size

WndSize with value

Sensor Lock / Unlock

Locks or Unlocks Sensor

Lock Sensor

Unlock Sensor

Reset to Default Settings Resets Sensor to Factory Default Settings

0.04 seconds < T < 0.8 seconds
Timing between Pulse groups > 1 second

Pulse Timing (T)

NOTE: Follow procedure for the TEACH/SET method
(highlighted in black box) chosen in the TEACH Selection menu.
Timeout is 60 seconds.

Teaching.. (SPt1)

TchSPt1 with measurement value, then to TchSPt2

Teaching..(SPt2)

TchSPt2 with measurement value, then back to Run mode

Teaching.. (TchA&D1)

Tch4mA and TchSPt1 with measurement value, then to TchA&D2

Teaching..(TchA&D2)

Tch20mA and TchSPt2 with measurement value, then

Teaching.. (Tch12mA)

Tch12mA with measurement value, then back to Run mode

Teaching.. (TchMdPt)

TchMdPt (teaches SPt in Switch Mode) with measurement value, then

Teaching.. (TchA&D)

Tch12mA and TchMdPt (teaches SPt in Switch Mode) with measurement

value, then back to Run mode

Set Mode to Alarm, then back to Run mode

Set Mode to Health, then back to Run mode

Set Mode to Switch , then back to Run mode

Set Mode to Window , then back to Run mode

Sensor Mode

Mode with current value

Run

Mode

back to Run mode

Refer to the Window size table for the acceptable values.

Содержание LTF



























































Результаты поиска

Содержание LTF

Отзывы:

Бренды по названию

Популярные бренды

Banner LTF, Инструкция по эксплуатации

Результаты поиска

Содержание LTF

Отзывы:

Бренды по названию

Популярные бренды