Banner LTF Скачать руководство пользователя страница 41

Страница: 41 / 60

June 22, 2023

LTF Time Of Flight Laser Distance Sensor Instruction Manual

Default

: Normal

Normal Display Orientation

Inverted Display Orientation

Sleep

The Sleep option sets when the display is put to sleep. Four timing options are available: 1, 5, 15, or 60 minutes. Sleep mode
is disabled by default. Sleep occurs in Run mode and any menu. To wake the sensor and return to the last viewed mode or

menu, press any button.

Navigate

›

DISPLAY

›

Sleep

Remote Input

: Not available

Default

: Disabled

Information Menu (INFO)

Use this menu to view model, part number (P/N), serial number (S/N), and firmware version (Version) information. Select one

of these options to view specific information for your sensor. This information is read-only.

Navigate

›

INFO

Remote Input

: Not available

Information Menu Map

MENU INFO

Go Back to Parent Menu

Select Menu Item

Press to Save Setting

Press and Hold to Go Back

to Run Mode

INFO Version

INFO Model

Version 1.0.0

Model LTF12I

INFO P/N

P/N 94849

INFO S/N

S/N F..S..P..D..

Reset Menu (RESET)

Use this menu to restore the sensor to the factory default settings.

Navigate

›

RESET.

Select Yes to apply the factory defaults; select No to return to the Reset option without changing

any sensor settings.

Remote Input

: Eight-pulse the remote input

Содержание LTF



























































Результаты поиска

Содержание LTF

Отзывы:

Бренды по названию

Популярные бренды

Banner LTF, Инструкция по эксплуатации

Результаты поиска

Содержание LTF

Отзывы:

Бренды по названию

Популярные бренды