Banner LTF Скачать руководство пользователя страница 34

Страница: 34 / 60

June 22, 2023

LTF Time Of Flight Laser Distance Sensor Instruction Manual

•
•

Timer

The Timer option sets the delays and timers. On/Off Delays and On/Off One-Shot timers can be programmed between 1 to

9999 ms (a value of 0 disables the delay/timer). The following figure defines how the delays/timers affect the output behavior.

Navigate:

›

D_OUT

›

Timer

Remote Input

: not available

Default

: 0 ms for all timers

Delays/Timers

Output

OFF Delay

ON Delay

Time

OFF 1-Shot

ON 1-Shot

OFF

(D = 1 - 9999 ms)

Some combinations of delays/timers are not allowed. The programming menu automatically disables invalid combinations of delays/timers. The following ta-
ble shows the allowable combinations of delays/timers.

Off Delay

Off One-Shot Timer

On Delay

On One-Shot Timer

Off Delay

(OffDly)

N/A

Off One-Shot Timer

(Off1Sho)

N/A

On Delay

(OnDly)

N/A

On One-Shot Timer

(On1Sho)

N/A

Polarity

The Polarity option sets the discrete output polarity to either PNP (current sourcing) or NPN (current sinking). The physical

wiring of the sensor and the sensor polarity setting must match.

Navigate

›

D_OUT

›

Polarity

Remote Input

: Not available

Default

: PNP

Input Menu (INPUT)

Use this menu to view or change the:

Multi-function input type
Active state of the remote input

Содержание LTF



























































Результаты поиска

Содержание LTF

Отзывы:

Бренды по названию

Популярные бренды

Banner LTF, Инструкция по эксплуатации

Результаты поиска

Содержание LTF

Отзывы:

Бренды по названию

Популярные бренды