Banner A-GAGE High-Resolution MINI-ARRAY MAHE6A Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 39

Banner A-GAGE High-Resolution MINI-ARRAY MAHE6A Скачать руководство пользователя страница 28

Error Number

Error Type

Action

1

Output Short

Check output load & wiring

2

E / R Mismatch

System must use same length emitter and receiver

3

Receiver Error

•

Check receiver cable

•

Replace receiver

4

Emitter Error

•

Check emitter cable

•

Replace emitter

5

Serial Comm

Check serial cable

6

EEPROM

•

Reconfigure PSF

•

Replace control module

•

Reconfigure blanking

7

CPU Error

Replace control module

8

Null / Span

Status

Emitter

OPERATIONAL (red): LED indicates power to the emitter is ON, and unit is operational.

Receiver

BLOCKED (red): LED indicates some of the array beams are blocked.
MARGINAL (yellow): LED indicates that array alignment is marginal.
ALIGNMENT (green): LED indicates that array alignment is satisfactory.
To improve alignment, adjust the position of the emitter and receiver until the green LED lights, making sure that no

unblanked beams are interrupted. Then use one of the methods in

System Alignment

(p. 14) to realign the system.

5.2 Diagnostics Routine

Emitter or receiver problems may be further diagnosed using the Diagnostics routine included with the MINI-ARRAY

software. Launch the program by selecting Diagnostics under the MINI-ARRAY menu or by pressing F2.
The Diagnostics screen displays the size of each emitter and receiver (expressed in the number of 64-element boards it

contains) and its functional status (or state). If an error has occurred, the specific problem beam channel is identified.

Additionally, if there is a problem with an emitter or receiver cable connection, a “No Response” message displays.

Figure 26. Diagnostics screen, accessible from the MINI-ARRAY menu

The Diagnostics routine also displays the part number and date code of the controller, information that may be useful if

Banner-assisted troubleshooting is required.

A-GAGE

®

High-Resolution MINI-ARRAY

®

28

www.bannerengineering.com - Tel: + 1 888 373 6767

«
...
26
27
28
29
30
...
»

Содержание A-GAGE High-Resolution MINI-ARRAY MAHE6A








































Отзывы:

Нет отзывов