Coupure de l’alimentation secteur
- Débrancher l’alimentation secteur.
Débrancher tous les autres câbles connectés au BeoVision 5.
Retirer le cadre avant et la face avant en tissu
- Faire sortir la partie inférieure du cadre avant puis la partie supérieure.
- Retirer 11 vis de la face avant en tissu.
- Faire sortir la partie inférieure de la face avant en tissu puis la laisser glisser
lentement vers le bas. Prière de voir page 6.22
Retrait et montage de la face avant
en tissu.
- Assembler les deux supports d’intervention en suivant le guide visuel à la page
6.26
Assemblage du support d’intervention
.
Démonter l’écran plasma
- Retirer 4 obturateurs à l’arrière du BeoVision 5. Voir page 6.27
Démontage de
l’écran plasma.
- Retirer les 4 vis dissimulées derrière les obturateurs.
- Il faut faire tourner deux vis de réglage de la position de l’écran plasma vers le bas
jusqu’à ce que l’écran ne puisse descendre davantage. Voir
➢
48.
- Débranchez les 4 câbles 3P447, 3P422, 60P448 et 60P449. Voir
➢
21.
- Laisser la partie supérieure de l’écran plasma basculer en s’éloignant de la partie
arrière du BeoVision 5. Voir
➢
49.
- Placer
l’écran plasma sur les deux supports d’intervention.
Retirer le couvercle arrière
- Débranchez les 3 câbles PC1, série et secteur. Voir
➢
49A.
- Retirer 4+21 vis afi n de desserrer le couvercle arrière. Voir page 6.29
Retrait du
couvercle arrière de l’écran plasma
et les pages suivantes.
Raccordement du tapis antistatique au châssis
- Raccorder le tapis antistatique au châssis mécanique (C). Voir
➢
10.
Prise de mesures
- Pour prendre des mesures, prière de voir page 5.26
Réglages après le remplacement
de PCB dans le panneau plasma.
Placer les modules sur le tapis antistatique
- Les
modules
doivent
être placés sur le tapis antistatique afi n de les protéger contre
les décharges électrostatiques.
Monter l’écran plasma
Le montage doit être fait dans l’ordre inverse du démontage de l’écran plasma. Il
faut faire tourner les deux vis de réglage de la position de l’écran plasma vers le
haut jusqu’à ce que la distance entre le haut du téléviseur (sans cadre avant) et le
haut de l’image soit de 70mm des deux côtés. Voir
➢
50C.
Rebrancher tous les fi ls
- Après le remplacement de modules, ne pas oublier de rebrancher tous les fi ls aux
fi ches comme auparavant. S’assurer que tous les fi ls sont branchés correctement.
Placer les fi ls dans leurs dispositifs de retenue
- Placer les divers fi ls dans les dispositifs de retenue correspondants.
Démontage, Français 6.11
Содержание BeoVision 5
