B&R Industrial Automation GmbH Power Panel 65 Скачать руководство пользователя страница 23

Страница: 23 / 112

Power Panel 65 • 4PP065.0351-P74

Power Panel 65 User's manual V2.21

System failure error codes

Incorrect configuration or defective hardware can cause a system failure error.

The error code is indicated by the red EPL Error LED using four switch-on phases. Each switch-on phase has a

duration of either 150 ms or 600 ms. The error code is repeated every 2 seconds.

Key

●

... 150 ms

... 600 ms

Pause

... 2 second delay

Error description

Error code displayed by red EPL LED

RAM error

●

Pause

●

Pause

Hardware error

●

Pause

●

Pause

2.4.4.4 ACT / LNK LEDs for the RJ45 interfaces

There are two additional LEDs each for the Ethernet and POWERLINK interfaces.

ACT

(orange)

LNK

(green)

LED

Color

Status

Description

No Ethernet or POWERLINK activity on the bus

ACT

Orange

Blinking

Ethernet or POWERLINK activity on the bus

LNK

Green

Link established to the remote station

2.4.5 Connection elements

Power supply

Ethernet interface

USB interfaces

POWERLINK interface

2.4.5.1 POWERLINK interface

Interface

Pinout

Terminal

POWERLINK

RXD

Receive signal

RXD\

Receive signal inverted

TXD

Transmit signal

Termination

TXD\

Transmit signal inverted

Termination

POWERLINK interface

Shielded RJ45 port

Termination

Содержание Power Panel 65

















































































































Результаты поиска

Содержание Power Panel 65

Отзывы:

Бренды по названию

Популярные бренды

B&R Industrial Automation GmbH Power Panel 65, Руководство пользователя

Результаты поиска

Содержание Power Panel 65

Отзывы:

Бренды по названию

Популярные бренды