B&C Technologies HP series Скачать руководство пользователя страница 6

Страница: 6 / 39

Anyone operating or servicing this machine must follow the safety rules in this manual.
Particular attention must be paid to the DANGER, WARNING, and CAUTION blocks which
appear throughout the manual

The lightening flash
and arrowhead within
the triangle is a
warning sign alerting
you of the presence of
dangerous voltage.

The exclamation point
within the triangle is a
warning sign alerting
you of important
instructions

concerning the machine and possible
dangerous conditions.

This warning symbol
alerts you to the
presence of possible
dangerous drive
mechanisms within
the machine. Guards

should always be in place when the
machine is in operation. Be careful
when servicing any drive mechanism.

This warning symbol
indicates the presence
of possibly dangerous
chemicals. Proper
precautions should be
taken when handling

corrosive or caustic material.

This warning symbol
indicates the presence
of hot surfaces that
could cause serious
burns. Stainless steel

and steam lines can become
extremely hot and should not be
touched.

This warning symbol
indicates the presence
of possible dangerous
pinch-points. Moving
mechanical parts can
crush an/or sever body
parts.

Before servicing any
equipment, make
certain it is
disconnected from the
electrical power

source. Never allow operation of the
machine when any safety device is
malfunctioning. Never bypass safety
devices.

Key Symbols

Содержание HP series








































Результаты поиска

Содержание HP series

Отзывы:

Похожие инструкции для HP series

Бренды по названию

Популярные бренды

B&C Technologies HP series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HP series

Отзывы:

Похожие инструкции для HP series

Бренды по названию

Популярные бренды