B&C Technologies HP series Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 39

background image

Installation

Theory of Operation

12

front of the machine and is accessed by
opening the cover door. Supplies, both
liquid and powder; may be added by
pulling the dispenser cups out and placing
the appropriate supply in each. Supplies are
flushed into the machine at the proper time
in the cycle, controlled by the micro
computer.

Holes are provided at the rear of the
machine for connection to an external,
central liquid supply unit. Electrical
connections are provided for the liquid
supply unit on a terminal strip inside the
rear control module. Refer to page for
connection details.

«
...
11
12
13
14
15
...
»

Содержание HP series








































Отзывы:

Нет отзывов

Похожие инструкции для HP series

Бренд: Gaggenau Страницы: 48

Бренд: Gaggenau Страницы: 48

Бренд: Gaggenau Страницы: 40

Бренд: Gaggenau Страницы: 68

Бренд: Daewoo Страницы: 16

Бренд: LASA Страницы: 60

Бренд: Scandium Страницы: 40

Бренд: NEFF Страницы: 32

Бренд: CDA Страницы: 40

Бренд: Lino Страницы: 164

Бренд: Stanley Страницы: 16

Бренд: OZTI Страницы: 24

Бренд: Hotpoint Страницы: 12

Бренд: BIEMMEDUE Страницы: 19

Бренд: Arctic Страницы: 60

Бренд: Indesit Страницы: 20

Бренд: Zanussi Electrolux Страницы: 22

XQG50-QF800 - 07-01

Бренд: Haier Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды