B&C Technologies HP series Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 39

background image

Wear Eye and hand protection when handling chemicals. Always avoid
direct contact with raw chemicals. Read the manufacturer’s directions for
accidental contact before handling chemicals. Ensure that an eye-rinse
facility and an emergency shower are within easy reach. Check at regular
intervals for chemical leaks.

26

Installation

External Chemical Supplies

The following procedures must be observed
when connecting any chemical injector to
the washer-extractor. See the figure for a
typical supply injection system setup.
Undiluted chemicals dripping can damage
the machine. Therefore, all chemicals
supply dispenser pumps must be mounted

below the washer’s injection point. All
dispenser tubing should also run below the
injection point. Loops do not prevent drips
if these instructions are not followed. Failure
to follow these instructions could damage
the machine and void the warranty.

Supply

Connection

Chemical
Dispenser
Pump

PCV Pipe

«
...
26
27
28
29
30
...
»

Содержание HP series








































Отзывы:

Нет отзывов

Похожие инструкции для HP series

Бренд: EAS Electric Страницы: 194

Бренд: Vax Страницы: 8

Бренд: Hotpoint Страницы: 56

Бренд: Matsui Страницы: 8

Бренд: Akai Страницы: 28

Бренд: Saba Страницы: 39

Бренд: Kärcher Страницы: 16

Бренд: Primotecq Страницы: 72

Бренд: Briggs & Stratton Страницы: 36

Бренд: NewAir Страницы: 24

Бренд: BorMann Страницы: 14

Бренд: Parmco Страницы: 28

Бренд: Iberna Страницы: 24

Бренд: Maytag Страницы: 36

FLOORWASH 1000 Battery

Бренд: NAMCO Страницы: 24

SUNJOE SPX4001-RM

Бренд: SNOWJOE Страницы: 18

Бренд: Hotpoint Страницы: 16

MDC4650AWB - Jet Clean II 24" Portable Dishwasher

Бренд: Maytag Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды