Bamato KP-210, Руководство пользователя

Страница: 26 / 48

26 GB
B
A
M
A
T
O
Bavarian Machine Tools
• Use the tool that is recommended in this manual.
In doing so, your mitre saw provides optimal per­
formance.
• Hands may never enter the processing zone when
the machine is in operation. Release the handle
button and switch off the machine prior to any op­
erations.
7. Before starting the equipment
•
The equipment must be set up where it can stand
securely. Secure the machine on a workbench or a
stand with 4 screws through the holes in the fixed
saw table (15).
•
All covers and safety devices have to be properly
fitted before the equipment is switched on.
•
It must be possible for the blade to run freely.
•
When working with wood that has been processed
before, watch out for foreign bodies such as nails
or screws, etc.
•
Before you press the ON/OFF switch check that
the saw blade is fitted correctly. Moving parts must
run smoothly.
•
Before you connect the equipment to the power
supply make sure the data on the rating plate are
dentical to the mains data.
Do not use the tool if the switch does not allow
you to switch from the ON state to the OFF state.
8. Attachment and operation
8.1 Attaching the saw (Fig1/2/3/4/5)
•
In order to adjust the rotary table (14) loosen the
set screw (26) approx. 2 turns.
•
Turn the rotary table (14) and pointer (12) to the
desired angle measurement on the scale (13) and
secure with the set screw (26).
•
Pressing the machine head (4) lightly downwards
and removing the locking bolt (23) from the motor
bracket at the same time disengages the saw from
the lowest position.
•
Swing the machine head (4) up until the release
lever (3) latches into place.
•
It is possible to secure the clamping device (7) to
the left or right on the stationary saw bench (15).
Insert the clamping device (7) in the hole on the rear
side of the stop rail (16) and secure it with the star
grip screw (7a).
•
Attach the workpiece supports (8) to the fixed saw
table (15) as shown in Figure 5 and fasten with the
screw (9).
•
It is possible to tilt the machine head (4) a max. 45°
to the left by loosening the set screw (22).
Noise
Total noise values determined in accordance with
EN 61029.
sound pressure level L
pA
99.6 dB(A)
uncertainty K
pA
3 dB
sound power level L
WA
112.6 dB(A)
uncertainty K
WA
3 dB
Wear hearing protection.
The effects of noise can cause a loss of hearing.
Vibration emission value a
h
≤
2.5 m/s²
uncertainty K
1.5 m/s²
The specified vibration value was established in ac ­
cordance with a standardized testing method. It may
change according to how the electric equipment is
used and may exceed the specified value in excep ­
tional circumstances;
The specified vibration value can be used to compare
the equipment with other electric power tools.
The specified vibration value can be used for initial
assessment of a harmful effect.
Reduce noise generation and vibration to a mini-
mum!
Use only equipment that is in perfect condition.
Maintain and clean the equipment regularly.
Adopt your way of working to the equipment.
Do not overload the equipment.
Have the equipment checked if necessary.
Switch off the equipment when not in use.
Residual risks
The machine has been built according to the state
of the art and the recognised technical safety re-
quirements. However, individual residual risks
can arise during operation.
• Health hazard due to electrical power, with the use
of improper electrical connection cables.
• Furthermore, despite all precautions having been
met, some non­obvious residual risks may still re­
main.
• Residual risks can be minimised if the „safety in­
structions“ and the „Proper use“ are observed
along with the whole of the operating instructions.
• Do not load the machine unnecessarily: excessive
pressure when sawing will quickly damage the saw
blade, which results in reduced output of the ma­
chine in the processing and in cut precision.
• When cutting plastic material, please always use
clamps: the parts which should be cut must always
be fixed between the clamps.
• Avoid accidental starting of the machine: the op­
erating button may not be pressed when inserting
the plug in an outlet.