manualshive.com logo in svg

BALZER Field Floater, Руководство по сборке

Поделиться
Скачать
BALZER Field Floater Скачать руководство пользователя страница 71

 71 

Testing 

The following initial setup operational tests are to be performed by qualified maintenance personnel 
prior to delivery to customer. Refer to Field Floater IV Grain Cart manual for further instructions on 
safety, tractor requirements and in field operations. 

1)  Attach tractor draw bar to grain cart hitch with properly sized hitch pin that has a retainer device. 

Attach safety chain to tractor. Crank trailer jack to slowly place pressure on draw bar. Move jack to 
storage location and secure. Connect PTO to tractor. Attach all hydraulic hoses. (Refer to Operation 
Sections of grain cart manual for more detail.) 

2)  Connect grain cart 7-pin light harness to tractor 7-pin connection. Verify left and right turn 

indicators, hazard lights and stop lights with tractor controls. 

3)  Connect Avery Weigh-Tronix controller to grain cart. Connect 

RED 

wire on Avery-Tronix 

controller to 

+12VDC

 on tractor. Connect 

BLACK 

wire on Avery Weigh-Tronix controller to 

Ground 

on Tractor. Zero Avery Weigh-Tronix controller and add weight to cart to verify operation. 

4)  Connect Joystick controller to grain cart. Connect 

RED

 wire on joystick controller to 

+12VDC 

on 

tractor. Connect 

BLACK

 wire on joystick controller to Ground on tractor. 

Содержание Field Floater












































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды