Baldor LD Series Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 37

background image

1-14 General Information

MN1269

Tools

There are a few basic tools recommended to install the “LD” Servo Control.

Recommended Tools

Description and Use

Slotted screw driver, medium size

Terminal strips, chassis and possibly transformer

Slotted, very small screw driver (or pot adjustment
tool

Potentiometer adjustment and screw terminal
connections

Phillips, screw driver medium large with 8” long
shank (required if replacing or adding servo control
cards

Add or remove modules

Phillips, screw driver medium

Input connections to AC bus power

Crescent Wrench (6” or 8”)

Disassemble packaging from chassis

VOM meter

Testing continuity, verifying Voltage, current,
polarity, etc.

A number of other common tools are recommended in order to do a proper job i.e. solder iron, solder,
crimp tools, wire stripper, etc.

Servo Systems Co. • 115 Main Road • P.O. Box 97 • Montville, NJ, 07045-0097

(973) 335-1007 • Toll Free: (800) 922-1103 • Fax: (973) 335-1661

www.servosystems.com

«
...
15
16
17
18
19
...
»

Содержание LD Series






































Отзывы:

Нет отзывов

Похожие инструкции для LD Series

Бренд: Jafar Страницы: 9

Бренд: Samsung Страницы: 6

Бренд: Samsung Страницы: 32

ACTIVE DRIVER M/M 1.1

Бренд: DAB Страницы: 10

Бренд: d&b audiotechnik Страницы: 3

ACTIVE DRIVER M/M 1.1

Бренд: DAB PUMPS Страницы: 38

Бренд: ICM Controls Страницы: 2

Бренд: Nedap Страницы: 20

Бренд: Rane Страницы: 2

Бренд: Vega Страницы: 20

Бренд: NAiS Страницы: 144

Бренд: Sunnen Страницы: 24

FAREX SR MINI SYSTEM

Бренд: RKC INSTRUMENT Страницы: 82

Бренд: Acuity Controls Страницы: 5

Бренд: Risco Страницы: 232

CompleteStat-Series CS9B-THO

Бренд: Bard Страницы: 2

Бренд: NXP Semiconductors Страницы: 20

Ratio Feeder J+ Advanced Series

Бренд: H.E. Anderson Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды