background image

Mooney 22/22H Pilots Instruction Manual  |  11

Copyright 2022 Baker Hughes Company. All rights reserved.

2. 

 Place Diaphragm Assembly in the pilot body with the 

diaphragm touching the grooved sealing surface of the pilot 

body. (Refer to Figure 11).

Figure 11

 - Placing Diaphragm Assembly on Pilot Body.

3.   Place Spring Housing on Pilot Body with vent connection 

in desired position. The standard factory installation will be 

with the vent facing directly away from the regulator.

Figure 12 

- Placing the Spring Housing on the Pilot Body.

4. 

Install Spring Housing Cap Screws. Use cap screws 

supplied and tighten evenly to 8 ft-lbs (10.8 Nm) torque.

5. 

 Install Spring and Spring Follower. Lubricate Spring 

Follower with a Petroleum Grease such as Lubriplate™ No. 

105.

Figure 13

 - Installing the Spring with lubricated Spring Follower: 

Lubricate with Petroleum Grease such as Lubriplate™ No. 

105.

6.   To avoid galling of adjusting screw, apply a small amount 

of lubricant (such as NEVER SEEZ™ by Bostik to the 

adjusting screw thread.

бA.  

PILOTS WITH THE RED, PLATED, BLUE, AND PURPLE 

       SPRINGS:

 Install Closing Cap with Adjusting Screw and 

 

       Sealing Nut and O-Ring.

Figure 14

 - Installing the closing cap assembly for Pilot with the 

Red, Plated, Blue, and Purple Springs.

Lubricate

Содержание Mooney 22 Series

















Отзывы: