background image

b  |  Baker Hughes

Copyright 2021 Baker Hughes Company. All rights reserved.

THESE INSTRUCTIONS PROVIDE THE CUSTOMER/OPERATOR WITH IMPORTANT PRO-

JECT-SPECIFIC REFERENCE INFORMATION IN ADDITION TO THE CUSTOMER/OPERA-

TOR’S NORMAL OPERATION AND MAINTENANCE PROCEDURES. SINCE OPERATION 

AND MAINTENANCE PHILOSOPHIES VARY, BAKER HUGHES COMPANY (AND ITS SUB-

SIDIARIES AND AFFILIATES) DOES NOT ATTEMPT TO DICTATE SPECIFIC PROCEDURES, 

BUT TO PROVIDE BASIC LIMITATIONS AND REQUIREMENTS CREATED BY THE TYPE OF 

EQUIPMENT PROVIDED. 
THESE INSTRUCTIONS ASSUME THAT OPERATORS ALREADY HAVE A GENERAL UN-

DERSTANDING OF THE REQUIREMENTS FOR SAFE OPERATION OF MECHANICAL AND 

ELECTRICAL EQUIPMENT IN POTENTIALLY HAZARDOUS ENVIRONMENTS. THERE-

FORE, THESE INSTRUCTIONS SHOULD BE INTERPRETED AND APPLIED IN CONJUNC-

TION WITH THE SAFETY RULES AND REGULATIONS APPLICABLE AT THE SITE AND 

THE PARTICULAR REQUIREMENTS FOR OPERATION OF OTHER EQUIPMENT AT THE 

SITE.
THESE INSTRUCTIONS DO NOT PURPORT TO COVER ALL DETAILS OR VARIATIONS 

IN EQUIPMENT NOR TO PROVIDE FOR EVERY POSSIBLE CONTINGENCY TO BE MET 

IN CONNECTION WITH INSTALLATION, OPERATION OR MAINTENANCE. SHOULD FUR-

THER INFORMATION BE DESIRED OR SHOULD PARTICULAR PROBLEMS ARISE WHICH 

ARE NOT COVERED SUFFICIENTLY FOR THE CUSTOMER/OPERATOR’S PURPOSES THE 

MATTER SHOULD BE REFERRED TO BAKER HUGHES.
THE RIGHTS, OBLIGATIONS AND LIABILITIES OF BAKER HUGHES AND THE CUSTOM-

ER/OPERATOR ARE STRICTLY LIMITED TO THOSE EXPRESSLY PROVIDED IN THE CON-

TRACT RELATING TO THE SUPPLY OF THE EQUIPMENT. NO ADDITIONAL REPRESENTA-

TIONS OR WARRANTIES BY BAKER HUGHES REGARDING THE EQUIPMENT OR ITS USE 

ARE GIVEN OR IMPLIED BY THE ISSUE OF THESE INSTRUCTIONS.
THESE INSTRUCTIONS ARE FURNISHED TO THE CUSTOMER/OPERATOR SOLELY TO 

ASSIST IN THE INSTALLATION, TESTING, OPERATION, AND/OR MAINTENANCE OF THE 

EQUIPMENT DESCRIBED. THIS DOCUMENT SHALL NOT BE REPRODUCED IN WHOLE 

OR IN PART WITHOUT THE WRITTEN APPROVAL OF BAKER HUGHES.

Содержание Masoneilan 21009 Series















Отзывы: