Baker Hughes Druck DPI 612, Инструкция по безопасности и быстрому запуску

Страница: 9 / 138

Copyright 2015 Baker Hughes Company.
English–DPI612 Safety and Quick Start Guide | 1
Introduction
The DPI 612 is a battery-powered instrument for electrical
measure and source operations. You can use the touch-
screen to display the different parameters. The DPI 612
instrument measures and displays, via user
interchangeable PM 620 pressure modules, Pneumatic or
Hydraulic Pressure/Vacuum generated by the instrument.
The type and range of pressure generation is dependent on
the model selected.
Models
The DPI 612 models are listed below together with the
recommended PM 620 pressure module rating.
DPI 612 - PFX (pFlex Pneumatic Calibrator)
• Range: –950 mbar to 20 bar (–13.5 to 300 psi)
• PM 620: 2 to 20 bar (3 to 300 psi)
DPI 612 - PFP (pFlexPro Pneumatic Calibrator)
• Range: –950 mbar to 100 bar (–13.5 to 1500 psi)
• PM 620: 20 to 100 bar (300 to 1500 psi)
DPI 612 - HFP (hFlexPro Hydraulic Calibrator)
• Range: 0 to 1000 bar (0 to 15,000 psi)
• PM 620: 200 to 1000 bar (3000 to 15,000 psi)
Safety
The manufacturer has designed this equipment to be safe
when operated using the procedures detailed in this
manual. Do not use this equipment for any other purpose
than that stated, the protection provided by the equipment
may be impaired.
This publication contains operating and safety instructions
that must be followed to make sure of safe operation and to
maintain the equipment in a safe condition. The safety
instructions are either warnings or cautions issued to
protect the user and the equipment from injury or damage.
Use qualified technicians
*
and good engineering practice
for all procedures in this publication.
Pressure
Do not apply pressures greater than the maximum working
pressure to the equipment.
Toxic Materials
There are no known toxic materials used in the construction
of this equipment.
Maintenance
The equipment must be maintained using the procedures
in this publication. Further manufacturer’s procedures
should be done by an authorized service agents or the
manufacturer’s service departments.
Technical Advice
For technical advice contact the manufacturer.
Symbols
Note: More marks and symbols are specified in the User
Manual (Druck DPI 612 Pressure Calibrator, 109M4017).
General Warnings
* A qualified technician must have the necessary technical
knowledge, documentation, special test equipment and
tools to carry out the required work on this equipment.
Symbol Description
This equipment meets the requirements of all
relevant European safety directives. The equipment
carries the CE mark.
This symbol, on the equipment, indicates that the
user should read the user manual.
This symbol, on the equipment, indicates a warning
and that the user should refer to the user manual.
Ce symbole, sur l'appareil, est un avertissement qui
indique que l'utilisateur doit consulter le manuel
d'utilisation.
USB ports: Type A; Mini-type B connector.
On / Off
Ground (Earth)
Do not dispose of this product as household waste.
Use an approved organization that collects and/or
recycles waste electrical and electronic equipment.
For more information, contact one of these:
- Our customer service department: Druck.com
- Your local government office.
WARNING
Before using this instrument,
read and understand the “Safety” section, the
user manual and the instructions for the
accessories / options / equipment you are
using it with.
Read and understand the applicable local
safety procedures.
It is dangerous to ignore the specified
warnings.
It is dangerous to ignore the specified limits
for the instrument or to use the instrument
when it is not in its normal condition. Use the
applicable protection and obey all safety
precautions.
Do not use the instrument in locations with
explosive gas, vapor or dust. There is a risk of
an explosion.
Do not use damaged equipment and use only
original parts supplied by the manufacturer.