Baker Hughes Druck DPI 612, Инструкция по безопасности и быстрому запуску

Страница: 13 / 138

Copyright 2015 Baker Hughes Company.
English–DPI612 Safety and Quick Start Guide | 5
7.3 DPI 612 - HFP: 1000 bar (14,500 psi)
7.3.1 Release the Pressure
Refer to Figure A5 and procedure below:
1. Turn the Refill valve fully counter-clockwise (Ref:
Item 11).
2. Turn the Release Valve Stem counter-clockwise, then
fully clockwise (Ref: Item 5).
Note: Fill the reservoir before attaching the device.
7.3.2 Filling, Priming
When using the DPI 612 - HFP for the first time, fill the
reservoir with the correct hydraulic fluid (Fluid type:
Demineralised water or a mineral oil (Recommended ISO
viscosity grade ≤ 22)). Fill and prime the pressure station.
If new, remove the red plastic blanking cover from the Test
port.
Fill the reservoir using the procedure that follows:
1. Turn the Refill valve fully counter-clockwise (Ref:
Item 11).
2. Turn the Volume adjuster fully clockwise (Ref:
Item 2.1).
3. Turn the Release Valve Stem fully counter-clockwise
(Ref: Item 5).
4. Remove the Priming pump piston/Release valve stem
assembly.
5. Fill the reservoir with the recommended fluid, (Fluid
type: Demineralised water or a mineral oil
(Recommended ISO viscosity grade ≤ 22)) 25 mm
approximately from the top.
6. Re-fit the Priming pump piston/Release valve stem
assembly
7. Turn the Release Valve Stem fully clockwise (Ref:
Item 5).
8. Turn the Refill valve fully clockwise, until finger tight
(Ref: Item 11).
9. Turn the Volume adjuster fully counter-clockwise (Ref:
Item 2.1).
10. Turn the Volume adjuster 5 turns clockwise (Ref:
Item 2.1).
11. Operate the Priming pump until the air is expelled and
fluid is visible at the Test port.
12. Fit the “Item under test” to the Test port use the existing
adaptor or the applicable AMC adaptor and applicable
seals.
13. Operate the Priming pump and prime the system to a
maximum pressure of 10 bar (145 psi).
14. Turn the Volume adjuster (Ref: Item 2.1) clockwise,
until the required pressure is indicated.
15. Turn the refill valve (Ref: Item 11) fully counter-
clockwise to allow full pressure control.
16. On completion of test, open the pressure release valve
one turn (Ref: Item 5) to release pressure before
disconnection of device under test.
7.3.3 Attach the Device Under Test
1. Open the refill valve fully counter-clockwise (Ref:
Item 11).
2. Open the pressure release valve counter-clockwise
(Ref: Item 5).
3. Use the applicable adaptor to attach the device, (Ref:
Figure A7).
8. Specification
8.1 General
WARNING
Pressurized gases and fluids
are dangerous. Before connecting or
disconnecting pressure equipment, safely
release all the pressure.
Ensure that the system is bled of excess air
before operation. If the item under test has a
large volume, pre-fill with the pressure fluid to
ensure that trapped air is kept to a minimum.
CAUTION
To prevent damage to the
pressure station, do not let dirt get into the
pressure mechanism. Before connecting
equipment, make sure it is clean.
CAUTION
Ice in the pressure mechanism
can cause damage. If the temperature is less
than 4 °C (39 °F), drain all water from the
DPI 612 - HFP.
Item Specification
Display LCD: Color display with touch-screen
Operating temperature –10 °C to +50 °C (50 °F to 122 °F)
+10 °C to +30 °C (optimized
calibration specification)
0 °C – 40 °C with optional mains
power supply.
Storage temperature –20 °C to 70 °C (–4 °F to 158 °F)
Ingress protection IP54 (EN 60529)
Operating humidity 0% to 90% Relative Humidify (RH)
non-condensing.
Shock/Vibration EN 61010 - 1, MIL - PRF - 28800F
Class 2.
Operating altitude Maximum 2000 metres (6560 ft)
EMC EN 61326
Electrical safety EN 61010 - 1
Power adaptor Input range: 100 – 240 VAC, 50 to
60 Hz, 300 – 150 mA, Installation
Category II.
Batteries (Rechargeable) Li–ion 14.1Wh Druck Part number:
CC3800GE. Nominal voltage 3.7 V
3800 mAh Charge temperature: 0 °
to 40 °C (32 ° to 104 °F) Discharge
temperature: –10 ° to 60 °C (14 ° to
140 °F). For best battery
performance, keep the temperature
less than 60 °C (140 °F).
Batteries (Non-
rechargeable)
8 × AA Alkaline
Pressure safety Pressure Equipment Directive -
class: sound engineering practice
(SEP) for group 2 fluids.
Pollution degree 2
Operating Environment Indoor use only. Not rated for use in
potential explosive atmospheres.
Pressure media Not rated for oxygen or other
explosive gases or liquids.