background image

2  |  

Baker Hughes

© 2020 Baker Hughes Company. All rights reserved.

THESE INSTRUCTIONS PROVIDE THE CUSTOMER/OPERATOR WITH IMPORTANT 

PROJECT-SPECIFIC REFERENCE INFORMATION IN ADDITION TO THE CUSTOMER/

OPERATOR’S NORMAL OPERATION AND MAINTENANCE PROCEDURES. SINCE 

OPERATION AND MAINTENANCE PHILOSOPHIES VARY, BAKER HUGHES (AND 

ITS SUBSIDIARIES AND AFFILIATES) DOES NOT ATTEMPT TO DICTATE SPECIFIC 

PROCEDURES, BUT TO PROVIDE BASIC LIMITATIONS AND REQUIREMENTS 

CREATED BY THE TYPE OF EQUIPMENT PROVIDED. 
THESE INSTRUCTIONS ASSUME THAT OPERATORS ALREADY HAVE A GENERAL 

UNDERSTANDING OF THE REQUIREMENTS FOR SAFE OPERATION OF MECHANICAL 

AND ELECTRICAL EQUIPMENT IN POTENTIALLY HAZARDOUS ENVIRONMENTS. 

THEREFORE, THESE INSTRUCTIONS SHOULD BE INTERPRETED AND APPLIED 

IN CONJUNCTION WITH THE SAFETY RULES AND REGULATIONS APPLICABLE AT 

THE SITE AND THE PARTICULAR REQUIREMENTS FOR OPERATION OF OTHER 

EQUIPMENT AT THE SITE.
THESE INSTRUCTIONS DO NOT PURPORT TO COVER ALL DETAILS OR VARIATIONS 

IN EQUIPMENT NOR TO PROVIDE FOR EVERY POSSIBLE CONTINGENCY TO BE MET 

IN CONNECTION WITH INSTALLATION, OPERATION OR MAINTENANCE. SHOULD 

FURTHER INFORMATION BE DESIRED OR SHOULD PARTICULAR PROBLEMS ARISE 

WHICH ARE NOT COVERED SUFFICIENTLY FOR THE CUSTOMER/OPERATOR'S 

PURPOSES THE MATTER SHOULD BE REFERRED TO BAKER HUGHES. 
THE RIGHTS, OBLIGATIONS AND LIABILITIES OF BAKER HUGHES AND THE 

CUSTOMER/OPERATOR ARE STRICTLY LIMITED TO THOSE EXPRESSLY PROVIDED 

IN THE CONTRACT RELATING TO THE SUPPLY OF THE EQUIPMENT. NO ADDITIONAL 

REPRESENTATIONS OR WARRANTIES BY BAKER HUGHES REGARDING THE 

EQUIPMENT OR ITS USE ARE GIVEN OR IMPLIED BY THE ISSUE OF THESE 

INSTRUCTIONS.
THESE INSTRUCTIONS ARE FURNISHED TO THE CUSTOMER/OPERATOR SOLELY 

TO ASSIST IN THE INSTALLATION, TESTING, OPERATION, AND/OR MAINTENANCE 

OF THE EQUIPMENT DESCRIBED. THIS DOCUMENT SHALL NOT BE REPRODUCED 

IN WHOLE OR IN PART WITHOUT THE WRITTEN APPROVAL OF BAKER HUGHES.

Содержание Consolidated 1511 Series

































Отзывы: