background image

INTRODUCTION

NOMENCLATURE

I-E96-408A   

1 - 3

NOMENCLATURE

GLOSSARY OF TERMS AND ABBREVIATIONS

Hardware

Nomenclature

Network Interface Slave Module
Loop Interface Module

INNIS01
INLIM03

Cables

Twinaxial Communication Cable

(PVC, stripped wire both ends)
(non-PVC, stripped wire both ends)

NKPL03
NKPL04

INFI-NET Adapter Cable (used with KCL cable)

NKTL01-3

Coaxial Communication Cable

(PVC, with BNC connectors)
(non-PVC, with BNC connectors)

NKCL01
NKCL02

ICL to ICL Cable

NKTT01

ICL to LIM Cable

(PVC)
(non-PVC)

NKLS04
NKLS14

ICL to NIS Cable

(PVC)
(non-PVC)

NKLS02
NKLS12

Termination Mounting Unit

(rear mount)
(front mount)

NTMU01
NTMU02

Term

Definition

Coaxial cable

A special type of communications cable that permits the 
transmission of data at high speed.

INFI-NET

Advanced data communication highway.

Plant Loop

Network 90

®

 data communication highway.

TM

Termination Module. Provides input/output connection 
between plant equipment and the INFI 90/Network 90 
modules.

TMU

Termination Mounting Unit. A card cage that provides 
housing for INFI 90/Network 90 termination modules.

Twinaxial cable

A cable composed of two insulated conductors that are 
twisted together and are attached or bound together with 
a common covering.

® Registered trademark of Elsag Bailey Process Automation.

Содержание Infi 90 NICL01

































Отзывы: