Bailey Infi 90 IMDSI12 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 49

background image

INSTALLATION

WIRING CONNECTIONS AND CABLING

WBPEEUI240752A0

3 - 7

WIRING CONNECTIONS AND CABLING

The DSI has three card edge connectors to supply logic power,
establish I/O expander bus communication and provide digital
inputs (P1, P2, P3 respectively).

Wiring

Installing the module in the MMU connects the digital input
module to the logic power (+5 VDC), necessary to drive the cir-
cuitry, at P1. It also connects P2 to the I/O expander bus for
communication with the control module. P1 and P2 connec-
tions require no additional wiring or cabling.

NOTE: You must install a dipshunt on the backplane of the MMU to
connect the I/O expander bus between the digital input module and
control module. Locate the modules so the bus can connect the
modules or they will not communicate.

Cable Connections

The IMDSI1

digital input module can use either a NTDI01

termination unit or an NIDI01 termination module for termi-
nation. Refer to Figure

to determine the cables to use with

the TU or TM.

FUSING

The IMDSI1

digital input module does not have any on board

fusing requirements.

Figure 3-3. Cable Connections and Termination

IMDSI1

T00105A

P1

P1

P3

P1

P3

P1

P2

P2

NKTM01/02

OR

NKTU02/12

NIDI01

IMDSI1

NTDI01

NKTU01/11

16 DIGITAL FIELD INPUTS
(24/48/125 VDC OR 120 VAC)

16 DIGITAL FIELD INPUTS
(24/48/125 VDC OR 120 VAC)

«
...
26
27
28
29
30
...
»

Содержание Infi 90 IMDSI12


















































Отзывы:

Нет отзывов

Похожие инструкции для Infi 90 IMDSI12

Бренд: ABB Страницы: 370

Бренд: ABB Страницы: 17

Бренд: ABB Страницы: 104

Бренд: ABB Страницы: 120

Бренд: ABB Страницы: 42

Бренд: Vasco Страницы: 32

Бренд: Abra Страницы: 16

Бренд: SAI Страницы: 16

Бренд: Hable Страницы: 3

Бренд: Quectel Страницы: 95

Бренд: ICAS Страницы: 51

Бренд: Icar Страницы: 40

Бренд: Icar Страницы: 86

Бренд: Icar Страницы: 39

Бренд: IBP Страницы: 12

Бренд: VAT Страницы: 27

Бренд: ICP DAS USA Страницы: 148

Бренд: ICMA Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды