Bailey Infi 90 IMDSI12 Скачать руководство пользователя страница 16

Страница: 16 / 49

INTRODUCTION

SPECIFICATIONS

WBPEEUI240752A0

1 - 7

Isolation
(IEC 1010-1, IEC 255, IEC 60)

Channel to channel and channel to
logic

Electromagnetic compatibility

Conducted transients

Electrostatic discharge
(IEC 1000-4-2, EN 61000-4-2)

Contact: ±6 kV
Air: ±8 kV

Magnetic and electromag-
netic fields

Power frequency magnetic field
(IEC 1000-4-8, EN 61000-4-8)

Continuous: 30 A/m (rms)
Short duration: 300 A/m (rms)

Pulse magnetic field
(IEC 1000-4-9, EN 61000-4-9)

Peak value: 300 A/m

Damped oscillatory magnetic
field, 0.1 MHz and 1 MHz
(IEC 1000-4-10, EN 61000-4-10)

Peak value: 30 A/m

    Radiated radio-frequency elec-
    tromagnetic field, 80 MHz to
    1GHz (ENV 50140)

Unmodulated rms: 10 V/m
Amplitude modulated: 80% AM (1 kHz)

    Radiated radio-frequency field,
    900 ±5 MHz
    (ENV 50204)

Unmodulated rms: 10 V/m
Pulse modulated: Duty cycle 50%
Rep. cycle 200 Hz

Table 1-5. Specifications

Property

Characteristic/Value

Test

Common Mode

Normal

Mode

IMDSI12/15

Insulation resistance
(100/500 VDC)

100 M

Ω

N/A

Dielectric VAC (45 - 65 Hz) or
VDC

1.4 kV rms/1min. or
1.95 kV DC/1min.

N/A

Impulse voltage (1.2/50 µS)

±2.55 kVp

±1 kVp

IMDSI13/14

Insulation resistance
(100/500 VDC)

100 M

Ω

N/A

Dielectric VAC (45 - 65 Hz) or
VDC

1 kV rms/1min. or
1.5 kV DC/1min.

N/A

Impulse voltage (1.2/50 µS)

±2 kVp

±1 kVp

Test

Common Mode

Normal

Mode

Voltage/current surge
(1.2/50 µS to 8/20 µS )
(IEC 1000-4-5, EN 61000-4-5)

±2 kVp

±1 kVp

Fast transient bursts
(IEC 1000-4-4, EN 61000-4-4)

±2 kVp

N/A

Damped oscillatory wave,
0.1 MHz and 1 MHz
(IEC 1000-4-12, EN 61000-4-12)

±2 kVp

±1 kVp

Ring wave
(IEC 1000-4-12, EN 61000-4-12)

±2 kVp

±1 kVp

Содержание Infi 90 IMDSI12


















































Результаты поиска

Содержание Infi 90 IMDSI12

Отзывы:

Похожие инструкции для Infi 90 IMDSI12

Бренды по названию

Популярные бренды

Bailey Infi 90 IMDSI12, Инструкция

Результаты поиска

Содержание Infi 90 IMDSI12

Отзывы:

Похожие инструкции для Infi 90 IMDSI12

Бренды по названию

Популярные бренды