background image

 

 

13 

ASSIGNMENT 

13.1  The Buyer shall not be entitled to assign the Contract or any part of it without the prior written consent of the Company. 
13.2  The Company may assign the Contract or any part of it to any person, firm or company. 

 

14 

FORCE MAJEURE 

The Company reserves the right to defer the date of delivery or to cancel the Contract or reduce the volume of the Goods ordered by the 
Buyer (without liability to the Buyer) if it is prevented from or delayed in the carrying on of its business due to circumstances beyond the 
reasonable control of the Company including, without limitation, acts of God, governmental actions, war or national emergency, riot, civil 
commotion, fire, explosion, flood, epidemic, lock-outs, strikes or other labour disputes (whether or not relating to either party's workforce), 
or  restraints  or  delays  affecting  carriers  or  inability  or  delay  in  obtaining  supplies  of  adequate  or  suitable materials  Provided  that,  if  the 
event  in  question  continues  for  a  continuous  period  in  excess  of  [180]  days,  the  Buyer  shall  be  entitled  to  give  [not  less  than  [3]  days] 
notice in writing to the Company to terminate the Contract. 

 

15 

GENERAL 

15.1  Each right or remedy of the Company under the Contract is without prejudice to any other right or remedy of the Company whether 

under the Contract or not. 

15.2  If any provision of the Contract is found by any court, tribunal or administrative body of competent jurisdiction to be wholly or partly 

illegal, invalid, void, voidable, unenforceable or unreasonable it shall to the extent of such illegality, invalidity, voidness, voidability, 
unenforceability  or  unreasonableness  be  deemed  severable  and  the  remaining  provisions  of  the  Contract  and  the  remainder  of 
such provision shall continue in full force and effect. 

15.3  Failure or delay by the Company in enforcing or partially enforcing any provision of the Contract will not be construed as a waiver of 

any of its rights under the Contract. 

15.4  Any waiver by the Company of any breach of, or any default under, any provision of the Contract by the Buyer will not be deemed a 

waiver of any subsequent breach or default and will in no way affect the other terms of the Contract. 

15.5  The  parties  to  this  Contract  do  not  intend  that  any  term  of  this  Contract  will  be  enforceable  by  virtue  of  the  Contracts  (Rights  of 

Third Parties) Act 1999 by any person that is not a party to it. 

15.6  The formation, existence, construction, performance, validity and all aspects of the Contract shall be governed by English law and 

the parties submit to the exclusive jurisdiction of the English courts. 

 

16 

COMMUNICATIONS 

16.1  All communications between the parties about this Contract must be in writing and delivered by hand or sent by pre-paid first class 

post or sent by facsimile transmission: 

16.1.1 

(in  case  of  communications  to  the  Company)  to  its  registered  office  or  such  changed  address  as  shall  be  notified  to  the 
Buyer by the Company; or  

16.1.2 

(in the case of the communications to the Buyer) to the registered office of the addressee (if it is a company) or (in any other 
case) to any address of the Buyer set out in any document which forms part of this Contract or such other address as shall 
be notified to the Company by the Buyer. 

16.2  Communications shall be deemed to have been received: 

16.2.1 

if sent by pre-paid first class post, 2 days (excluding Saturdays, Sundays and bank and public holidays within the UK) after 
posting (exclusive of the day of posting); 

16.2.2 

if delivered by hand, on the day of delivery; 

16.2.3 

if sent by facsimile transmission on a working day prior to 4.00 p.m., at the time of transmission and otherwise on the next 
working  day.  Communications  addressed  to  the  Company  shall  be  marked  for  the  attention  of  the  designated  purchasing 
agent for the buyer. 

 

17 

EXPORT 

17.1 

In these Conditions “Incoterms” means the international rules for the interpretation of trade terms of the International Chamber of 
Commerce as in force at the date when the Contract is made.  Unless the context otherwise requires, any term or expression which 
is defined in or given a particular meaning by the provisions of Incoterms shall have the same meaning in these Conditions, but if 
there is any conflict between the provisions of Incoterms and these Conditions, the latter shall prevail. 

17.2  Where the Goods are supplied for export from the United Kingdom, the provisions of this Condition 17 shall (subject to any special 

terms agreed in writing between the Buyer and the Company) apply notwithstanding any other provision of these Conditions. 

17.3  The  Buyer  shall  be  responsible  for  complying  with  any  legislation  or  regulations  governing  the  importation  of  the  Goods  into  the 

country of destination and for the payment of any duties on them. 

17.4  Unless  otherwise  agreed in writing  between  the Buyer  and the  Company, the  Goods shall  be  delivered  fob the  air  or sea  port  of 

shipment and the Company shall be under no obligation to give notice under section 32(3) of the Sale of Goods Act 1979. 

17.5 

The Buyer shall be responsible for arranging for testing and inspection of the Goods at the Company’s premises before shipment. 
The Company shall have no liability for any claim in respect of any defect in the Goods which would be apparent on inspection and 
which is made after shipment, or in respect of any damage during transit. 

 
 
 
 

Содержание TN-800













































Отзывы: