background image

 

 

TECHNICAL SPECIFICATIONS 

 

Table Length x Width 

63" 

x 7” (1600 x 176mm) 

Back Gauge Length 

21.5” (546mm) 

Maximum Pressure 

33 tons (29.9metric tons) 

Throat Depth 

7.87" (200mm) 

Distance Between Housings 

51.3" (1304mm) 

Distance From Table To Ram 

11.8" (300mm) 

Stroke Distance 

3.9" (100mm) 

Adjustment of Ram Travel 

3.1" (80mm) 

Approach Speed 

3.5"/sec. (90mm/sec.) 

Working Speed 

.394"/sec. (10mm/sec.) 

Return Speed 

3.3"/sec. (85mm/sec.) 

Power 

220V, 3-phase, 60hz, 30A 

Main Motor 

7.5hp (5.5kw) 220V, 3ph, 60hz, 20A 

Back Gauge Motor (X Axis) 

3/4hp (550w) 220V, 3ph, 60hz, 3.2A 

Bend Depth Motor (Y Axis) 

1/8hp (120w) 220V, 3ph, 60hz, 1A 

Hydraulic Reservoir Capacity 

28gal. (106L) 

Hydraulic Pump 

Axial Piston, 4568psi x 0.61ci/r (31.5MPa x 10mL/r) 

Maximum Hydraulic Pressure 

3190psi (22MPa) 

Shipping Weight 

4000lbs. (1800kg) 

Shipping Dimensions 

83" x 47" x 82" (2108 x 1194 x 2083mm) 

Footprint Dimensions 

97" x 91" x 82" (2464 x 2312 x 2083mm) 

Based on a material tensile strength of   60000 PSI 

– mild steel 

 
 

TECHNICAL SUPPORT 

Our technical support department can be reached at 920.684.4990 and asking for the support 
desk for purchased machines. Tech Support handles questions on machine setup, schematics, 
warranty issues, and individual parts needs: (other than die sets and blades). 
For specific application needs or future machine purchases contact the Sales Department at: 
[email protected]Phone: 920.684.4990, or Fax: 920.684.3944. 

 

Note: The photos and illustrations used in this manual are representative only and 

may not depict the actual color, labeling or accessories and may be intended to illustrate 
technique only.

 

 

Note: The specifications and dimensions presented here are subject to change 

without prior notice due to improvements of our products. 

Содержание BP-3305CNC

























































Отзывы: