background image

WIRING

At installation, be sure to comply with the following require-
ments:

IMPORTANT!

• Disconnect power to the unit before attempting any

connection or service to the unit

Do not bundle or route signal lines with power lines

Keep all lines as short as possible

Use twisted pair shielded wire for all output wiring

Observe all applicable local electrical codes

For the AC power connections use three wire sheathed cable with
overall cable diameter of 0.2" to 0.45" (5mm to 12mm). For signal
output use 18 to 22 gauge (0.25 mm

2

 to 0.75mm

2

) shielded wire.

Overall cable diameter between 0.12" to 0.35" (3mm to 9mm).

WIRING FOR REMOTE PRIMO

®

 CONFIGURATION

Wiring between the detector and the Primo amplifier comes complete
from the factory. If your installation requires the use of conduit, the
following are recommended steps for wiring of the detector to the
amplifier.

1. Remove the junction box lid. Carefully remove the wires connected

to the terminal blocks that run to the Primo amplifier. Note which
wire goes into which terminal. The chart below may be of assis-
tance for reference of wire color and terminal connection.

2. Run cable through conduit from Primo amplifier location, retaining

the wiring of the cable to the amplifier as supplied.

3. Complete conduit assembly on both ends and rewire cable into

junction box as wired when received.  See wiring diagram below.

Connection No.

Description

Wire color

11

Coil

Green

12

Coil

Yellow

13

Main Shield

Yellow/green

45

Electrode

White

44*

Electrode Shield

Black

46

Electrode

Brown

40

Empty Pipe

Pink

44*

Empty Pipe Shield

Black

*Connections with the No. 44 are lying on the same potential

Remote style Primo Amplifier models can be ordered with longer
cable than our standard stock lengths of the standard cable; 15, 30,
50 and 100 feet. The following chart shows the cable style options
and the maximum flow medium temperature that can exist in the
application environment at a given length of that cable.

7

Wiring for Remote Primo Configuration

44
40
44
46
44
45

13
12
11

  

  

shield (black)

pink

brown

shield (black)
white

yellow/green

yellow
green

green

yellow

yellow/green

white

shield (black)

brown

pink

shield (black)

45

44

46

44

40

44

13  12 11 

Содержание Magnetoflow Mag Meter





















Отзывы: