Backyard Discovery Cedar Mountain 5007 Скачать руководство пользователя страница 7

Страница: 7 / 88

RECOMMENDED GROUND COVERS

Suggested Material ........Uncompressed Depth

Double Shredded Bark Mulch  ...........9"
Uniform Wood Chips  ........................12"
Fine Gravel  .......................................12"
Fine Sand ..........................................12"

SELECTING THE CORRECT LOCATION FOR YOUR PLAY PRODUCT IS IMPORTANT

FOR YOUR CHILDREN’S SAFETY AND THE PRODUCT’S LONGEVITY

Safe Play Area:

• The safe play area refers to a zone extending 6' beyond the gym set on all sides,

including the space above the gym set.

• The ground surface must be level. Installing your gym set on sloping ground can cause

it to lean or "rack". This leaning puts additional stress on all connections and joints and
in time will cause those connections to loosen and fail.

• The safe play area must be free of all structures, landscaping, trees and branches,

rocks, wires, and other obstacles to safe play. Children can be seriously injured running
or swinging into these obstacles.

• Remove all tripping hazards from the safe play area. Tripping hazards include: roots,

stumps, rocks, landscaping, sprinkler heads, railroad ties, plumbing and electrical
connections.

• Do not install your gym set over concrete, gravel, asphalt, packed earth or any other

hard surface. The following is a list of recommended ground covers from the Consumer
Product Safety Commission.

A FALL ON TO A HARD SURFACE COULD RESULT IN SERIOUS INJURY

Any edging used to contain the ground must be
beyond the safe play area.
(Ex. Landscape timbers or railroad ties)

Dimensions:

• The Next Generation has One layout option.

Layout

Ground Dimension

Safe Play Area*

6"81/2"x5'10"

17'-10"x18'-9"

*Level Ground Surface - See below
• Additional accessories may increase the size of the Safe Play Area.
• Max fall height 90"

General Information:

Your set has been designed and engineered for children

only and for residential use only.

A maximum of 150 lbs. per child is recommended for

play activities designed for individual use.

A maximum of 120 lbs. per child is recommended for

play activities designed for multiple child use.

A maximum of 9 children is recommended for this unit.

SAFETY AND ASSEMBLY INFORMATION

Page 4 - SAFETY & ASSEMBLY

Next Generation 5007 10-0409 Version 4

Meijer.com

Содержание Cedar Mountain 5007

























































































Результаты поиска

Содержание Cedar Mountain 5007

Отзывы:

Похожие инструкции для Cedar Mountain 5007

Бренды по названию

Популярные бренды

Backyard Discovery Cedar Mountain 5007, Инструкция по сборке

Результаты поиска

Содержание Cedar Mountain 5007

Отзывы:

Похожие инструкции для Cedar Mountain 5007

Бренды по названию

Популярные бренды