Backyard Discovery Cedar Mountain 5007 Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 88

background image

AT THIS POINT, MAKE SURE THE SET IS AT ITS PERMANENT LOCATION. MAKE SURE TO STAKE DOWN
THE SET WITH GROUND STAKES. ATTACH THE SLIDE TO THE SET USING 1” STEP BOLTS, BARREL
NUTS, LOCK WASHERS AND FLAT WASHERS. USE HOLES IN SLIDE AND MARK HOLE LOCATIONS,
MOVE SLIDE OUT OF THE WAY AND DRILL THE HOLES WITH 3/8" DRILL BIT. ATTACH AS ILLUSTRATED

Note hardware for attaching the slide is included in the 5007 tower kit.

The 8ft. slide will require 2 bolts

The 10ft. slide will require 3 bolts

© Copyright Playground Inc

If you need assistance with parts or have assembly questions, please call

Customer Service at 866-362-1123. Our regular office hours are

Monday through Friday, 7:00 a.m. to 4:00 p.m. Central Time

LEISURE TIME PRODUCTS

Part # 5077 • 8 Foot Slide

Part # 5087 • 10 Foot Slide

Next Generation

8 & 10 Foot Slide

ASSEMBLY INSTRUCTIONS

Put the Slide in position as shown on the rear of the playset. Use
the holes in the slide to mark hole locations. Move the slide out of
the way and drill three 3/8” holes on your marks all the way
through the floor of the clubhouse.

Move the slide back into position and insert the 1" Step Bolt from the
top into the slide. The 1/4" Barrel Nuts Insert with Flat Washers and
Lock Washers into the holes you drilled from the underside of the
clubhouse floor. Tighten securely, but don't over tighten.

10 Foot

Slide

1/4"

BARREL

HEAD

NUT

1/4 X 1"

STEP
BOLT

5/16"

INTERNAL

TOOTH

LOCK

WASHER

5/16"
FLAT

WASHER

NOTE: SLIDE WILL FIT TIGHTLY
AND IT MAY BE NECESSARY TO
SQUEEZE IT INTO POSITION.

SLIDE

WOOD FLOOR

BOLT

5/16"

LOCK WASHER

FLAT WASHER

BARREL NUT

Put the Slide in position as shown on the rear of the playset. Use
the holes in the slide to mark hole locations. Move the slide out of
the way and drill two 3/8” holes on your marks all the way through
the floor of the clubhouse.

Move the slide back into position and insert the 1" Step Bolt from the
top into the slide. The 1/4" Barrel Nuts Insert with Flat Washers and
Lock Washers into the holes you drilled from the underside of the
clubhouse floor. Tighten securely, but don't over tighten.

8 Foot

Slide

1/4"

BARREL

HEAD

NUT

1/4 X 1"

STEP
BOLT

5/16"

INTERNAL

TOOTH

LOCK

WASHER

5/16"
FLAT

WASHER

SLIDE

WOOD FLOOR

BOLT

5/16"

LOCK WASHER

FLAT WASHER

BARREL NUT

Meijer.com

«
...
66
67
68
69
70
...
»

Содержание Cedar Mountain 5007

























































































Отзывы:

Нет отзывов

Похожие инструкции для Cedar Mountain 5007

Бренд: Sunjoy Страницы: 9

Бренд: VERTBAUDET Страницы: 51

Grow With Me 3in1

Бренд: Jamara Страницы: 12

Бренд: PlaySafe Страницы: 13

Бренд: PlaySafe Страницы: 15

Бренд: Take a Swing Страницы: 16

Бренд: Backyard Discovery Страницы: 60

Бренд: Sunjoy Страницы: 13

Pyramido 657045

Бренд: pedalo Страницы: 8

Бренд: Kolcraft Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды