background image

The Cedar Mountain Swingset

From Backyard Discovery

Backyard Discovery

3001 N Rouse Ave

Pittsburg, KS 66762

www.swingsetsonline.com

Sales: 855-308-6871

Support: 800-856-4445

YOU MUST START HERE!

Use these assembly instructions to begin assembly of your Cedar Mountain swingset.

1.

The Cedar Mountain is made from individually packaged components. Each 
component has its own assembly instructions in the box.

2.

Build each component according to the instructions in the respective 
component box(es) 

except for the Tunnel.

3.

For the tunnel only, you MUST use the instructions in this package. DO NOT USE 
THE INSTRUCTIONS IN THE TUNNEL/ ROCK WALL BOX!

4.

Once all components are complete, attach them to the respective towers to 
make the Cedar Mountain configuration as shown. Attach the towers together 
using the tunnel and the instructions in this package!

5.

The swing beam can be attached to the back of either fort without causing a 
play conflict.

6.

Build the rock wall using the original tunnel/rock wall instructions in the box and 
attach it to one of the fort openings as directed in the rock wall instructions.

7.

DO NOT INSTALL THE 10’ SLIDE AND THE 8’ SLIDE NEXT TO EACH OTHER! YOU 
MUST LEAVE A TOWER WALL PANEL IN PLACE AS A SPACER TO SEPARATE THE 
TWO SLIDES. MOUNTING THEM CLOSE WILL CAUSE A PLAY CONFLICT AND 
MAY RESULT IN INJURY!

8.

DO NOT MOUNT THE MONKEY BARS ON THE SAME TOWER/SIDE OF THE 
TOWER AS EITHER SLIDE. THIS WILL CAUSE A PLAY CONFLICT AND MAY RESULT 
IN INJURY!

Meijer.com

Содержание Cedar Mountain 5007

























































































Отзывы: