manualshive.com logo in svg

Bacharach Oxor III, Руководство по эксплуатации и техническому обслуживанию, Страница: 9 / 28

Поделиться
Скачать
Bacharach Oxor III Скачать руководство пользователя страница 9

Instruction 0019-9337

5

Oxor® III

3.3  Front Panel Pushbuttons

Note that a push button may perform several functions, depending on what 

screen is being displayed at the time.

 

I/O

 

• 

Turns analyzer ON/OFF. There is a 60 second warm-up and 

a 5 second turn-off-delay period.

 

 

•

 Places the analyzer into either its Setup or Calibration Mode 

when used in conjunction with the 

ENTER 

or 

HOLD 

button.

 

 

 

 

•

 Causes the displayed value to increase or change while in 

the Calibration or Setup Mode.

 

 

•

 Causes the displayed value to decrease or change while in 

the Calibration or Setup Mode.

 

ENTER

 

•

 Starts a test – pump ON. 

 

 

•

 Sets up the analyzer to be placed into its Calibration Mode 

when held down with the analyzer OFF. (Used in conjunc-

tion with the 

I/O

 button.)

 

 

•

 Stores the displayed value and automatically steps to the 

next screen when pressed during calibration or setup. 

 

 

•

 Displays the O

2

 screen when held down for 2 seconds while 

in the Calibration Mode. 

 

 

•

 Aborts turn-off and keeps the analyzer turned ON when 

pressed during either the 5 second turn-off-delay period.

 

HOLD

 

•

 Freezes the display and stops the pump during a test. 

 

 

•

 Starts a printout when pressed 

twice 

with the pump run-

ning, or when pressed 

once 

with the pump OFF.

 

 

• 

Sets up the analyzer to be placed into its Setup Mode when 

held down with the analyzer OFF. (Used in conjunction with 

the 

I/O

 button.)

 LIGHT

  Toggles the back light ON and OFF. 

Содержание Oxor III





























Отзывы:

Нет отзывов