manualshive.com logo in svg

Azbil Micro Flow CMS 0200, Руководство пользователя, Страница: 18 / 52

Поделиться
Скачать
Azbil Micro Flow CMS 0200 Скачать руководство пользователя страница 18

10

Chapter 3. Mounting and Wiring

 

z

Rc connection

• 

   Coating  sealant

 

Coat the pipe threads, except the two nearest the tip, with an appro-

priate amount of sealant.  

Remove dirt or burrs from the inside of the pipe.

Right

Wrong

Sealant

Sealant

•    Piping  connection

 

When connecting the piping, hold the flowmeter by putting a 

wrench on the flange.

Flange

Resin cover

Body

Pipe

 

z

UNF connection

•    Fitting  connection

 

When connecting a fitting, hold the flowmeter by putting a wrench 

on the flange.

 Handling Precautions

•  Do not grip and turn the 

main part of the device.  

Doing so might cause 

damage or leakage.

•  When connecting the pip-

ing, do not hold the flow-

meter by the resin cover. 

Doing so might damage 

the cover.

•  Observe the specified 

tightening torque.

 

z

Gas flow

 Handling Precautions

•  Gas must flow through the meter in the direc-

tion of the arrow on the side of the flow chan-
nel. Flow in the opposite direction cannot be 
measured accurately.

Fitting

Tightening torque

CMS9500/0002/0005/0020/0050:  40 to 45 N•m

CMS0200/0500:  

50 to 60 N•m

Resin cover

Flange

Body

Gas

Gas

Содержание Micro Flow CMS 0200





















































Отзывы:

Нет отзывов