Azbil Micro Flow CMS 0200 Скачать руководство пользователя страница 15

Страница: 15 / 52

Chapter 3. Mounting and Wiring

CAUTION

Observe the following when using this flowmeter for oxygen gas:

• Piping should be done by a specialist experienced in handling oxygen gas, observing

general precautions related to oxygen gas.

• Use degreased pipes and parts.

• Be sure to remove foreign matter, burrs, etc. from the pipes before connecting this flow-

meter.

Do not remove the resin cover and disassemble the piping connector part. Doing so could

cause damage.
When carrying or installing this device, never hold it by the resin cover.

Doing so could damage the cover, or the device could slip and fall, causing an injury.

Installation

Installation location

Avoid installing the device where it will be subject to conditions such

as the following.

• Ambient temperature colder than -10 ˚C or hotter than 60 °C

• Humidity higher than 90 % RH

• Sudden temperature fluctuations causing dew condensation

• Corrosive gas or flammable gas atmosphere

• Large amounts of dust, salt, iron powder or other conductive sub-

stances, water droplets, oil mist, or organic solvents

• Direct vibration or shock

• Direct sunlight

• Water or rain

• Splashing by fluids (e.g. oil, chemicals)

• Strong magnetic or electrical field

Behavior when the flow rate greatly exceeds the measurement range

If the flow rate exceeds the high limit for measurement, the cor-

rect value may not be displayed or output. Be sure to use the device

within the measurement range stated in the specifications.

If the flow rate exceeds 120 % of the high limit, the display alternately

shows the flow rate and

ALH1

. If the flow rate increases further, the

display does not show

ALH1

, but shows lower values than the actual

flow rate. Note that if the flow rate suddenly becomes excessive,

ALH1

may not be displayed. Especially when this device is used for flow

control, make sure to take appropriate measures, such as controlling

the supply pressure or using a throttle valve, so that even at maxi-

mum control output (100 %), the flow rate does not exceed 120 % of

the high limit of the range.

Flow rate

indication

Flow rate indication

High limit

120 % of high limit

Display

Flow rate

range

Flow rate and

ALH

alternately

Содержание Micro Flow CMS 0200





















































Результаты поиска

Содержание Micro Flow CMS 0200

Отзывы:

Бренды по названию

Популярные бренды

Azbil Micro Flow CMS 0200, Руководство пользователя

Результаты поиска

Содержание Micro Flow CMS 0200

Отзывы:

Бренды по названию

Популярные бренды