Axopar 37 ST Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 44

Axopar 37 ST Скачать руководство пользователя страница 33

5.3 SEPTIC SYSTEM

TOILET

The toilet is used with a separate operating switch. For more information on
the device, see the manual for the toilet. Before using the toilet, open the water
intake cock, which is behind the service hatch. Do not forget to close the cock
after use.

Clean the toilet with a mild cleaner. Never use cleaning agents or deodorants
which contain pine oil, formaldehyde or chlorine, nor corro- sive or petroleum
-based agents. These can damage plastic and rubber parts in the toilet. Lubricate
the pump shaft with Vaseline to increase the service life of the seal. Flush the
toilet system thoroughly with fresh water when the boat is not in use. Never
put any other objects but toilet paper in the toilet. Under no circumstances
is it allowed to flush paper towels, fabric or rubber products, hard objects, oil

products or solvents down the toilet. In order to avoid various damages, you
must also not pour hotter than lukewarm water into the

TOILET

1. Toilet
2.

Toilet flush water inlet and septic tank sea-cock

3.

Holding tank

4.

Breather valve for septic tank

5.

Deck suction fitting

6.

Septic crusher

Copyright @ Aivan Oy

Axopar
Axopar 37

Drawing:

Axopar 37 CTT

Scale:

Date:

1:50

27.11.2015

Aivan Oy

Laivakatu 3

00150 Helsinki, Finland

+358 (0)10 423 6401

[email protected]

www.aivan.fi

Axopar 37 TT

1

2

3

6

4

5

33

«
...
31
32
33
34
35
...
»

Содержание 37 ST













































Отзывы:

Нет отзывов